Machining an AR15 lower receiver

Thread Modes

Machining an AR15 lower receiver

doubleboost Offline

Super Moderator

Posts: 1,459
Threads: 159
Joined: Feb 2012
Location: Northern England

06-20-2012, 04:48 PM

Great pictures
I like those clamps with the copper tips Drool

If we start playing with guns we will get locked up Jawdrop

Even modifying a air rifle above 12 ftlb is a prison job
John

http://www.youtube.com/user/doubleboost

Like Post

« Next Oldest | Next Newest »

Messages In This Thread

Machining an AR15 lower receiver - by Highpower - 06-20-2012, 04:35 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 04:38 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 04:39 PM

RE: Machining an AR15 lower receiver - by EdK - 06-20-2012, 04:47 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 04:58 PM

RE: Machining an AR15 lower receiver - by EdK - 06-20-2012, 05:03 PM

RE: Machining an AR15 lower receiver - by doubleboost - 06-20-2012, 04:48 PM

RE: Machining an AR15 lower receiver - by EdK - 06-20-2012, 04:55 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 05:02 PM

RE: Machining an AR15 lower receiver - by stevec - 12-01-2013, 07:28 AM

RE: Machining an AR15 lower receiver - by TomG - 06-20-2012, 05:10 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 05:32 PM

RE: Machining an AR15 lower receiver - by TomG - 06-20-2012, 05:41 PM

RE: Machining an AR15 lower receiver - by ETC57 - 06-20-2012, 06:12 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-20-2012, 07:30 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 09:30 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-21-2012, 01:38 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-21-2012, 12:28 AM

RE: Machining an AR15 lower receiver - by RobWilson - 06-21-2012, 09:12 AM

RE: Machining an AR15 lower receiver - by TomG - 06-21-2012, 01:49 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-21-2012, 04:19 PM

RE: Machining an AR15 lower receiver - by TomG - 06-21-2012, 04:33 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-21-2012, 04:56 PM

RE: Machining an AR15 lower receiver - by doubleboost - 06-21-2012, 03:03 PM

RE: Machining an AR15 lower receiver - by DaveH - 06-21-2012, 03:26 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-21-2012, 07:55 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-21-2012, 09:58 PM

RE: Machining an AR15 lower receiver - by RobWilson - 06-22-2012, 10:51 AM

RE: Machining an AR15 lower receiver - by TomG - 06-21-2012, 10:17 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-22-2012, 12:06 AM

RE: Machining an AR15 lower receiver - by Mayhem - 06-21-2012, 10:30 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-22-2012, 12:27 AM

RE: Machining an AR15 lower receiver - by TomG - 06-22-2012, 06:28 AM

RE: Machining an AR15 lower receiver - by Highpower - 06-22-2012, 08:34 AM

RE: Machining an AR15 lower receiver - by DaveH - 06-22-2012, 09:25 AM

RE: Machining an AR15 lower receiver - by TOM REED - 06-22-2012, 09:36 AM

RE: Machining an AR15 lower receiver - by Highpower - 06-22-2012, 04:29 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-29-2012, 08:31 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-30-2012, 02:24 AM

RE: Machining an AR15 lower receiver - by DaveH - 06-29-2012, 08:38 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-29-2012, 09:19 PM

RE: Machining an AR15 lower receiver - by TomG - 06-29-2012, 08:46 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-30-2012, 10:03 AM

RE: Machining an AR15 lower receiver - by ScrapMetal - 07-01-2012, 01:08 AM

RE: Machining an AR15 lower receiver - by Highpower - 07-01-2012, 08:59 AM

RE: Machining an AR15 lower receiver - by doubleboost - 07-01-2012, 10:49 AM

RE: Machining an AR15 lower receiver - by Highpower - 07-01-2012, 12:23 PM

RE: Machining an AR15 lower receiver - by doubleboost - 07-01-2012, 12:42 PM

RE: Machining an AR15 lower receiver - by NevadaBlue - 07-23-2012, 10:52 AM

RE: Machining an AR15 lower receiver - by Highpower - 07-23-2012, 12:04 PM

RE: Machining an AR15 lower receiver - by d65 - 11-30-2013, 09:49 PM

RE: Machining an AR15 lower receiver - by Highpower - 12-22-2013, 07:26 AM

Users browsing this thread: 3 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me