MetalworkingFun Forum › Machining › Projects v
Quest -- A Good Steady Rest

Thread Modes
Quest -- A Good Steady Rest
Bill Gruby
Unregistered
 
#6
06-20-2012, 10:49 AM
The centers were then hogged out on a CNC machine by a friend in the trades. 5" was taken out. These rings are 7075 Aluminum. You need two because of the overlapping hinge, it is an integral part.

"Billy G"


Attached Files Thumbnail(s)
   
Reply
Thanks given by:


Messages In This Thread
Quest -- A Good Steady Rest - by Bill Gruby - 06-20-2012, 10:20 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-20-2012, 10:39 AM
RE: Quest -- A Good Steady Rest - by lazylathe - 06-20-2012, 10:39 AM
RE: Quest -- A Good Steady Rest - by Highpower - 06-20-2012, 10:40 AM
RE: Quest -- A Good Steady Rest - by TomG - 06-20-2012, 10:43 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-20-2012, 10:49 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-20-2012, 10:56 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-20-2012, 11:13 AM
RE: Quest -- A Good Steady Rest - by ETC57 - 06-20-2012, 12:49 PM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-20-2012, 02:17 PM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-20-2012, 02:33 PM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-20-2012, 03:00 PM
RE: Quest -- A Good Steady Rest - by DaveH - 06-20-2012, 03:10 PM
RE: Quest -- A Good Steady Rest - by doubleboost - 06-20-2012, 03:24 PM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-20-2012, 03:53 PM
RE: Quest -- A Good Steady Rest - by EdK - 06-20-2012, 03:54 PM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-20-2012, 03:58 PM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-21-2012, 06:56 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-21-2012, 07:06 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-21-2012, 07:10 AM
RE: Quest -- A Good Steady Rest - by krv3000 - 06-21-2012, 07:31 AM
RE: Quest -- A Good Steady Rest - by stevec - 06-21-2012, 07:40 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-21-2012, 08:12 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-21-2012, 09:39 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-21-2012, 09:46 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-21-2012, 11:34 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-21-2012, 11:43 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-21-2012, 11:50 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-21-2012, 12:00 PM
RE: Quest -- A Good Steady Rest - by doubleboost - 06-21-2012, 05:02 PM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-22-2012, 07:19 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-22-2012, 09:54 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-22-2012, 09:58 AM
RE: Quest -- A Good Steady Rest - by ScrapMetal - 06-22-2012, 03:06 PM
RE: Quest -- A Good Steady Rest - by doubleboost - 06-22-2012, 03:19 PM
RE: Quest -- A Good Steady Rest - by Mayhem - 06-22-2012, 09:54 PM
RE: Quest -- A Good Steady Rest - by DaveH - 06-23-2012, 07:06 AM
RE: Quest -- A Good Steady Rest - by November X-ray - 06-23-2012, 08:13 AM
RE: Quest -- A Good Steady Rest - by ozzie46 - 06-23-2012, 08:38 AM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-23-2012, 12:52 PM
RE: Quest -- A Good Steady Rest - by ETC57 - 06-25-2012, 09:16 PM
RE: Quest -- A Good Steady Rest - by Highpower - 06-26-2012, 06:45 AM
RE: Quest -- A Good Steady Rest - by ETC57 - 06-27-2012, 01:39 PM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 07-04-2012, 12:41 PM
RE: Quest -- A Good Steady Rest - by stevec - 07-04-2012, 05:30 PM
RE: Quest -- A Good Steady Rest - by TomG - 06-27-2012, 03:11 PM
RE: Quest -- A Good Steady Rest - by Bill Gruby - 06-29-2012, 06:47 AM
RE: Quest -- A Good Steady Rest - by krv3000 - 06-27-2012, 06:25 PM
RE: Quest -- A Good Steady Rest - by b4dyc - 06-28-2012, 04:22 PM



Users browsing this thread: 3 Guest(s)