Clamp Knurling Tool

Hello There, Guest! Register

Thread Modes

Project Clamp Knurling Tool

EdK

Offline

Whipping Boy

Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota

#92

10-17-2016, 07:02 PM

(10-17-2016, 06:02 PM)TomG Wrote: Ed,

Did you try plunge milling for the roughing out part? It's quicker and a lot easier on the end mill.

Tom

Yup, I'm following your videos almost to the 'T'. Plunge milling is so much quicker and easier on the mill and the VFD. The fan on my VFD didn't even come on while I was plunge milling. I do have an auxiliary fan inside the enclosure that runs as long as there's 220VAC turned on to the enclosure so that's what keeps the VFD cooled when I plunge mill.

Ed

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Clamp Knurling Tool - by EdK - 12-30-2014, 06:36 PM

RE: Clamp Knurling Tool - by EdK - 12-31-2014, 07:20 PM

RE: Clamp Knurling Tool - by TomG - 12-31-2014, 07:55 PM

RE: Clamp Knurling Tool - by EdK - 12-31-2014, 09:20 PM

RE: Clamp Knurling Tool - by stevec - 01-01-2015, 07:57 AM

RE: Clamp Knurling Tool - by dallen - 12-31-2014, 11:06 PM

RE: Clamp Knurling Tool - by PixMan - 01-01-2015, 12:18 AM

RE: Clamp Knurling Tool - by DaveH - 01-01-2015, 07:49 AM

RE: Clamp Knurling Tool - by EdK - 01-01-2015, 11:56 AM

RE: Clamp Knurling Tool - by TomG - 01-01-2015, 12:05 PM

RE: Clamp Knurling Tool - by EdK - 01-01-2015, 12:10 PM

RE: Clamp Knurling Tool - by TomG - 01-01-2015, 01:51 PM

RE: Clamp Knurling Tool - by rleete - 01-01-2015, 12:49 PM

RE: Clamp Knurling Tool - by rleete - 01-01-2015, 12:52 PM

RE: Clamp Knurling Tool - by EdK - 01-01-2015, 01:22 PM

RE: Clamp Knurling Tool - by DaveH - 01-01-2015, 01:28 PM

RE: Clamp Knurling Tool - by EdK - 01-01-2015, 01:43 PM

RE: Clamp Knurling Tool - by Mayhem - 01-01-2015, 07:47 PM

RE: Clamp Knurling Tool - by EdK - 01-01-2015, 07:50 PM

RE: Clamp Knurling Tool - by Mayhem - 01-01-2015, 08:01 PM

RE: Clamp Knurling Tool - by EdK - 01-01-2015, 08:20 PM

RE: Clamp Knurling Tool - by Mayhem - 01-01-2015, 10:42 PM

RE: Clamp Knurling Tool - by stevec - 01-02-2015, 08:17 AM

RE: Clamp Knurling Tool - by EdK - 01-02-2015, 10:01 AM

RE: Clamp Knurling Tool - by Arbalest - 01-02-2015, 09:33 AM

RE: Clamp Knurling Tool - by EdK - 01-02-2015, 10:04 AM

RE: Clamp Knurling Tool - by Highpower - 01-02-2015, 10:38 AM

RE: Clamp Knurling Tool - by Arbalest - 01-02-2015, 12:12 PM

RE: Clamp Knurling Tool - by the penguin - 01-02-2015, 12:57 PM

RE: Clamp Knurling Tool - by EdK - 01-02-2015, 01:36 PM

RE: Clamp Knurling Tool - by the penguin - 01-02-2015, 01:50 PM

RE: Clamp Knurling Tool - by EdK - 01-02-2015, 04:02 PM

RE: Clamp Knurling Tool - by Arbalest - 01-02-2015, 02:16 PM

RE: Clamp Knurling Tool - by Dr Stan - 01-02-2015, 10:39 PM

RE: Clamp Knurling Tool - by EdK - 01-03-2015, 10:15 AM

RE: Clamp Knurling Tool - by Mayhem - 01-03-2015, 10:50 AM

RE: Clamp Knurling Tool - by EdK - 01-03-2015, 11:03 AM

RE: Clamp Knurling Tool - by EdK - 01-03-2015, 06:10 PM

RE: Clamp Knurling Tool - by DaveH - 01-03-2015, 06:50 PM

RE: Clamp Knurling Tool - by TomG - 01-03-2015, 06:53 PM

RE: Clamp Knurling Tool - by the penguin - 01-03-2015, 07:08 PM

RE: Clamp Knurling Tool - by EdK - 01-03-2015, 11:01 PM

RE: Clamp Knurling Tool - by TomG - 01-03-2015, 11:13 PM

RE: Clamp Knurling Tool - by EdK - 01-04-2015, 10:21 AM

RE: Clamp Knurling Tool - by Sunset Machine - 01-04-2015, 10:53 AM

RE: Clamp Knurling Tool - by EdK - 01-04-2015, 11:13 AM

RE: Clamp Knurling Tool - by PixMan - 01-04-2015, 10:04 AM

RE: Clamp Knurling Tool - by EdK - 01-04-2015, 10:35 AM

RE: Clamp Knurling Tool - by Sunset Machine - 01-04-2015, 12:09 PM

RE: Clamp Knurling Tool - by EdK - 01-04-2015, 12:11 PM

RE: Clamp Knurling Tool - by Sunset Machine - 01-04-2015, 12:27 PM

RE: Clamp Knurling Tool - by EdK - 01-28-2015, 08:20 PM

RE: Clamp Knurling Tool - by EdK - 04-05-2016, 09:45 PM

RE: Clamp Knurling Tool - by Vinny - 04-05-2016, 09:50 PM

RE: Clamp Knurling Tool - by EdK - 04-05-2016, 10:01 PM

RE: Clamp Knurling Tool - by Roadracer_Al - 04-05-2016, 10:19 PM

RE: Clamp Knurling Tool - by dallen - 04-05-2016, 10:46 PM

RE: Clamp Knurling Tool - by f350ca - 04-05-2016, 11:12 PM

RE: Clamp Knurling Tool - by EdK - 10-05-2016, 03:48 PM

RE: Clamp Knurling Tool - by DaveH - 10-05-2016, 05:27 PM

RE: Clamp Knurling Tool - by EdK - 10-08-2016, 04:07 PM

RE: Clamp Knurling Tool - by f350ca - 10-08-2016, 04:13 PM

RE: Clamp Knurling Tool - by EdK - 10-08-2016, 05:04 PM

RE: Clamp Knurling Tool - by DaveH - 10-09-2016, 04:29 PM

RE: Clamp Knurling Tool - by EdK - 10-10-2016, 05:06 PM

RE: Clamp Knurling Tool - by DaveH - 10-10-2016, 05:09 PM

RE: Clamp Knurling Tool - by Vinny - 10-10-2016, 05:40 PM

RE: Clamp Knurling Tool - by EdK - 10-10-2016, 05:45 PM

RE: Clamp Knurling Tool - by Vinny - 10-10-2016, 06:10 PM

RE: Clamp Knurling Tool - by EdK - 10-11-2016, 04:42 PM

RE: Clamp Knurling Tool - by wawoodman - 10-12-2016, 02:39 PM

RE: Clamp Knurling Tool - by TomG - 10-12-2016, 05:03 PM

RE: Clamp Knurling Tool - by EdK - 10-12-2016, 05:59 PM

RE: Clamp Knurling Tool - by Dr Stan - 10-12-2016, 06:47 PM

RE: Clamp Knurling Tool - by wawoodman - 10-12-2016, 07:29 PM

RE: Clamp Knurling Tool - by Dr Stan - 10-12-2016, 08:09 PM

RE: Clamp Knurling Tool - by TomG - 10-12-2016, 09:17 PM

RE: Clamp Knurling Tool - by Dr Stan - 10-12-2016, 11:06 PM

RE: Clamp Knurling Tool - by PixMan - 10-13-2016, 06:56 AM

RE: Clamp Knurling Tool - by the penguin - 10-13-2016, 07:04 AM

RE: Clamp Knurling Tool - by wawoodman - 10-13-2016, 03:17 PM

RE: Clamp Knurling Tool - by EdK - 10-14-2016, 05:05 PM

RE: Clamp Knurling Tool - by Vinny - 10-14-2016, 05:35 PM

RE: Clamp Knurling Tool - by TomG - 10-15-2016, 02:09 PM

RE: Clamp Knurling Tool - by EdK - 10-15-2016, 05:04 PM

RE: Clamp Knurling Tool - by EdK - 10-16-2016, 04:33 PM

RE: Clamp Knurling Tool - by DaveH - 10-16-2016, 07:41 PM

RE: Clamp Knurling Tool - by PixMan - 10-17-2016, 11:25 AM

RE: Clamp Knurling Tool - by EdK - 10-17-2016, 04:54 PM

RE: Clamp Knurling Tool - by TomG - 10-17-2016, 06:02 PM

RE: Clamp Knurling Tool - by EdK - 10-17-2016, 07:02 PM

RE: Clamp Knurling Tool - by f350ca - 10-17-2016, 06:50 PM

RE: Clamp Knurling Tool - by EdK - 10-17-2016, 07:06 PM

RE: Clamp Knurling Tool - by TomG - 10-17-2016, 07:14 PM

RE: Clamp Knurling Tool - by f350ca - 10-17-2016, 07:20 PM

RE: Clamp Knurling Tool - by EdK - 10-21-2016, 03:12 PM

RE: Clamp Knurling Tool - by Vinny - 10-21-2016, 06:28 PM

RE: Clamp Knurling Tool - by PixMan - 11-02-2016, 06:46 PM

RE: Clamp Knurling Tool - by EdK - 12-12-2016, 06:05 PM

RE: Clamp Knurling Tool - by TomG - 12-13-2016, 05:53 PM

RE: Clamp Knurling Tool - by EdK - 12-13-2016, 07:39 PM

RE: Clamp Knurling Tool - by EdK - 01-08-2017, 06:28 PM

RE: Clamp Knurling Tool - by wawoodman - 01-08-2017, 06:43 PM

RE: Clamp Knurling Tool - by EdK - 01-10-2017, 05:50 PM

RE: Clamp Knurling Tool - by TomG - 01-10-2017, 08:18 PM

RE: Clamp Knurling Tool - by EdK - 01-14-2017, 03:58 PM

RE: Clamp Knurling Tool - by Old Minger - 01-14-2017, 04:21 PM

RE: Clamp Knurling Tool - by TomG - 01-14-2017, 04:32 PM

RE: Clamp Knurling Tool - by EdK - 01-14-2017, 05:00 PM

RE: Clamp Knurling Tool - by wawoodman - 01-14-2017, 10:53 PM

RE: Clamp Knurling Tool - by wawoodman - 01-14-2017, 05:07 PM

RE: Clamp Knurling Tool - by EdK - 01-15-2017, 12:02 PM

RE: Clamp Knurling Tool - by Vinny - 01-14-2017, 05:42 PM

RE: Clamp Knurling Tool - by f350ca - 01-14-2017, 06:09 PM

RE: Clamp Knurling Tool - by Mayhem - 01-14-2017, 11:20 PM

RE: Clamp Knurling Tool - by EdK - 01-15-2017, 09:59 AM

RE: Clamp Knurling Tool - by TomG - 01-15-2017, 11:00 AM

RE: Clamp Knurling Tool - by stevec - 01-17-2017, 08:57 AM

RE: Clamp Knurling Tool - by Mayhem - 01-15-2017, 10:13 AM

RE: Clamp Knurling Tool - by EdK - 01-15-2017, 11:27 AM

RE: Clamp Knurling Tool - by krv3000 - 01-15-2017, 05:55 PM

RE: Clamp Knurling Tool - by DaveH - 01-16-2017, 06:59 PM

RE: Clamp Knurling Tool - by TomG - 01-17-2017, 12:37 PM

RE: Clamp Knurling Tool - by wawoodman - 01-17-2017, 01:47 PM

RE: Clamp Knurling Tool - by EdK - 01-25-2017, 04:36 PM

RE: Clamp Knurling Tool - by TomG - 01-25-2017, 07:17 PM

RE: Clamp Knurling Tool - by Wongster - 01-26-2017, 07:07 AM

RE: Clamp Knurling Tool - by wawoodman - 01-26-2017, 02:26 PM

Users browsing this thread: 6 Guest(s)