|
home made mill
|
|
06-20-2016, 05:15 PM
well I got to work this morning and got a old base plate of a old press tool 30mm thick cut it up in to lumps with the gas axe then set one of the apprentices milling them up yes I no its cheating but its good practise for them to clock big lumps in any way tonight I made new scruws for the X and Y handels right pics
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
|
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
home made mill - by krv3000 - 06-19-2016, 03:58 PM
RE: home made mill - by Micktoon - 06-19-2016, 05:46 PM
RE: home made mill - by krv3000 - 06-20-2016, 05:15 PM
RE: home made mill - by krv3000 - 07-02-2016, 02:52 PM
RE: home made mill - by krv3000 - 07-02-2016, 02:57 PM
RE: home made mill - by Micktoon - 07-02-2016, 06:10 PM
RE: home made mill - by Mayhem - 07-02-2016, 07:31 PM
RE: home made mill - by krv3000 - 07-03-2016, 12:18 PM
RE: home made mill - by pepi - 07-04-2016, 06:07 AM
RE: home made mill - by krv3000 - 07-04-2016, 01:34 PM
RE: home made mill - by krv3000 - 07-08-2016, 04:37 PM
RE: home made mill - by rleete - 07-08-2016, 06:50 PM
RE: home made mill - by Mayhem - 07-08-2016, 08:24 PM
RE: home made mill - by krv3000 - 07-10-2016, 03:07 PM
RE: home made mill - by pepi - 07-10-2016, 10:05 PM
RE: home made mill - by krv3000 - 07-11-2016, 02:00 PM
RE: home made mill - by Micktoon - 07-11-2016, 06:25 PM
RE: home made mill - by krv3000 - 07-12-2016, 04:45 PM
RE: home made mill - by krv3000 - 07-25-2016, 04:11 PM
RE: home made mill - by EdK - 07-25-2016, 04:12 PM
RE: home made mill - by krv3000 - 08-01-2016, 01:13 PM
RE: home made mill - by EdK - 08-01-2016, 04:21 PM
RE: home made mill - by oldskoolron - 08-19-2016, 05:26 AM
RE: home made mill - by krv3000 - 10-01-2016, 02:16 PM
RE: home made mill - by Mayhem - 10-01-2016, 09:24 PM
RE: home made mill - by EdK - 10-02-2016, 09:27 AM
RE: home made mill - by Roadracer_Al - 10-02-2016, 11:33 AM
RE: home made mill - by Dr Stan - 10-14-2016, 07:07 PM
RE: home made mill - by krv3000 - 10-13-2016, 04:11 PM
RE: home made mill - by Micktoon - 10-13-2016, 04:27 PM
RE: home made mill - by krv3000 - 10-14-2016, 05:42 PM
RE: home made mill - by RobWilson - 10-15-2016, 02:26 AM
RE: home made mill - by krv3000 - 10-22-2016, 02:53 PM
RE: home made mill - by krv3000 - 10-29-2016, 04:08 PM
RE: home made mill - by Micktoon - 10-30-2016, 05:14 AM
RE: home made mill - by krv3000 - 10-30-2016, 06:10 PM
RE: home made mill - by krv3000 - 12-03-2016, 06:39 AM
RE: home made mill - by pepi - 12-03-2016, 07:19 AM
RE: home made mill - by TomG - 12-03-2016, 11:55 AM
RE: home made mill - by krv3000 - 12-03-2016, 01:20 PM
RE: home made mill - by f350ca - 12-03-2016, 01:25 PM
RE: home made mill - by awemawson - 12-03-2016, 01:46 PM
RE: home made mill - by Dr Stan - 12-03-2016, 02:18 PM
RE: home made mill - by awemawson - 12-03-2016, 03:01 PM
RE: home made mill - by krv3000 - 12-04-2016, 03:49 AM
RE: home made mill - by krv3000 - 12-11-2016, 05:50 PM
RE: home made mill - by Seanlogie - 02-05-2017, 03:57 AM
RE: home made mill - by krv3000 - 02-06-2017, 05:40 PM
RE: home made mill - by Micktoon - 02-06-2017, 05:53 PM
RE: home made mill - by Mayhem - 02-07-2017, 05:55 AM
RE: home made mill - by krv3000 - 02-07-2017, 06:03 PM
RE: home made mill - by wawoodman - 02-07-2017, 07:03 PM
RE: home made mill - by krv3000 - 02-08-2017, 05:19 PM
RE: home made mill - by krv3000 - 02-12-2017, 12:56 PM
RE: home made mill - by Micktoon - 02-12-2017, 04:05 PM
RE: home made mill - by krv3000 - 02-20-2017, 06:58 PM
RE: home made mill - by Mayhem - 02-21-2017, 06:55 AM
RE: home made mill - by krv3000 - 02-21-2017, 02:44 PM
RE: home made mill - by Pete O - 02-21-2017, 04:40 PM
RE: home made mill - by krv3000 - 02-22-2017, 07:58 PM
RE: home made mill - by Pete O - 02-23-2017, 06:13 PM
RE: home made mill - by Pete O - 02-23-2017, 06:25 PM
RE: home made mill - by Mayhem - 02-24-2017, 06:55 AM
RE: home made mill - by krv3000 - 02-24-2017, 04:52 PM
RE: home made mill - by krv3000 - 02-27-2017, 05:43 PM
|
