Surface plate in a roll around tool box

Hello There, Guest! Register

Thread Modes

Surface plate in a roll around tool box

JScott Offline

Offline

Sophmore

Posts: 240
Threads: 30
Joined: Mar 2014
Location: Planeta Rica, Colombia

#5

06-16-2016, 12:07 PM

Just an FYI. If anyone is looking at one of these roll around carts they are $99.99 at HF for Father's Day weekend.

http://www.harborfreight.com/580-lb-capa...OSJ9%0D%0A

JScott, proud to be a member of MetalworkingFun Forum since Mar 2014.

Reply

Thanks given by: EdK

« Next Oldest | Next Newest »

Messages In This Thread

Surface plate in a roll around tool box - by JScott - 05-04-2016, 11:49 AM

RE: Surface plate in a roll around tool box - by Highpower - 05-04-2016, 02:43 PM

RE: Surface plate in a roll around tool box - by pepi - 05-05-2016, 07:53 AM

RE: Surface plate in a roll around tool box - by JScott - 05-05-2016, 08:37 AM

RE: Surface plate in a roll around tool box - by JScott - 06-16-2016, 12:07 PM

RE: Surface plate in a roll around tool box - by EdK - 06-16-2016, 04:20 PM

RE: Surface plate in a roll around tool box - by JScott - 06-17-2016, 08:46 AM

RE: Surface plate in a roll around tool box - by EdK - 06-23-2016, 06:54 AM

RE: Surface plate in a roll around tool box - by JScott - 06-23-2016, 09:16 AM

RE: Surface plate in a roll around tool box - by EdK - 06-23-2016, 11:22 AM

RE: Surface plate in a roll around tool box - by JScott - 06-23-2016, 11:53 AM

RE: Surface plate in a roll around tool box - by zmotorsports - 06-24-2016, 04:21 PM

RE: Surface plate in a roll around tool box - by EdK - 06-30-2016, 09:21 PM

RE: Surface plate in a roll around tool box - by Vinny - 06-30-2016, 09:31 PM

RE: Surface plate in a roll around tool box - by EdK - 06-30-2016, 10:17 PM

RE: Surface plate in a roll around tool box - by JScott - 07-01-2016, 08:47 AM

RE: Surface plate in a roll around tool box - by EdK - 07-01-2016, 09:07 AM

RE: Surface plate in a roll around tool box - by EdK - 10-03-2016, 05:41 PM

RE: Surface plate in a roll around tool box - by the penguin - 10-03-2016, 06:05 PM

RE: Surface plate in a roll around tool box - by f350ca - 10-03-2016, 06:57 PM

RE: Surface plate in a roll around tool box - by EdK - 10-03-2016, 07:38 PM

RE: Surface plate in a roll around tool box - by Pete O - 10-03-2016, 07:08 PM

RE: Surface plate in a roll around tool box - by Vinny - 10-03-2016, 08:31 PM

RE: Surface plate in a roll around tool box - by pepi - 10-03-2016, 10:22 PM

RE: Surface plate in a roll around tool box - by EdK - 10-04-2016, 05:36 AM

RE: Surface plate in a roll around tool box - by pepi - 10-04-2016, 05:52 AM

Users browsing this thread: 1 Guest(s)