MetalworkingFun Forum › Machining › General Metalworking Discussion v
OnShape, a Free 3D CAD Program

Thread Modes
OnShape, a Free 3D CAD Program
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
The following 1 user Likes TomG's post:
Highpower (01-17-2016)
#24
01-17-2016, 08:36 AM
(01-17-2016, 06:16 AM)Mayhem Wrote: Well Tom is getting on in years - perhaps he needs the optics to see the keypad Big Grin

It was so quiet around here last week. Happyyes
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:


Messages In This Thread
OnShape, a Free 3D CAD Program - by TomG - 01-15-2016, 07:21 PM
RE: OnShape, a Free 3D CAD Program - by Pete O - 01-16-2016, 12:51 AM
RE: OnShape, a Free 3D CAD Program - by awemawson - 01-16-2016, 03:17 AM
RE: OnShape, a Free 3D CAD Program - by TomG - 01-16-2016, 09:44 AM
RE: OnShape, a Free 3D CAD Program - by awemawson - 01-16-2016, 10:38 AM
RE: OnShape, a Free 3D CAD Program - by EdK - 01-16-2016, 11:38 AM
RE: OnShape, a Free 3D CAD Program - by awemawson - 01-16-2016, 12:20 PM
RE: OnShape, a Free 3D CAD Program - by awemawson - 01-16-2016, 12:28 PM
RE: OnShape, a Free 3D CAD Program - by EdK - 01-16-2016, 12:30 PM
RE: OnShape, a Free 3D CAD Program - by EdK - 01-16-2016, 05:32 PM
RE: OnShape, a Free 3D CAD Program - by awemawson - 01-16-2016, 02:36 PM
RE: OnShape, a Free 3D CAD Program - by TomG - 01-16-2016, 07:15 PM
RE: OnShape, a Free 3D CAD Program - by Highpower - 01-17-2016, 06:33 AM
RE: OnShape, a Free 3D CAD Program - by TomG - 01-17-2016, 08:26 AM
RE: OnShape, a Free 3D CAD Program - by EdK - 01-16-2016, 07:34 PM
RE: OnShape, a Free 3D CAD Program - by EdK - 01-16-2016, 07:55 PM
RE: OnShape, a Free 3D CAD Program - by Mayhem - 01-16-2016, 07:56 PM
RE: OnShape, a Free 3D CAD Program - by EdK - 01-16-2016, 07:58 PM
RE: OnShape, a Free 3D CAD Program - by TomG - 01-16-2016, 08:01 PM
RE: OnShape, a Free 3D CAD Program - by Pete O - 01-17-2016, 06:14 AM
RE: OnShape, a Free 3D CAD Program - by TomG - 01-17-2016, 08:34 AM
RE: OnShape, a Free 3D CAD Program - by Vinny - 01-17-2016, 11:04 AM
RE: OnShape, a Free 3D CAD Program - by Dr Stan - 01-17-2016, 03:27 PM
RE: OnShape, a Free 3D CAD Program - by Vinny - 01-17-2016, 06:28 PM
RE: OnShape, a Free 3D CAD Program - by Mayhem - 01-17-2016, 06:16 AM
RE: OnShape, a Free 3D CAD Program - by TomG - 01-17-2016, 08:36 AM
RE: OnShape, a Free 3D CAD Program - by Mayhem - 01-17-2016, 08:55 AM
RE: OnShape, a Free 3D CAD Program - by TomG - 01-17-2016, 01:13 PM
RE: OnShape, a Free 3D CAD Program - by EdK - 01-17-2016, 12:37 PM
RE: OnShape, a Free 3D CAD Program - by DaveH - 01-17-2016, 01:58 PM
RE: OnShape, a Free 3D CAD Program - by awemawson - 01-17-2016, 04:59 PM
RE: OnShape, a Free 3D CAD Program - by rleete - 01-17-2016, 08:00 PM
RE: OnShape, a Free 3D CAD Program - by Shawn - 01-17-2016, 08:37 PM
RE: OnShape, a Free 3D CAD Program - by Pete O - 01-17-2016, 09:56 PM
RE: OnShape, a Free 3D CAD Program - by Vinny - 01-18-2016, 12:27 AM
RE: OnShape, a Free 3D CAD Program - by Shawn - 01-18-2016, 01:56 AM
RE: OnShape, a Free 3D CAD Program - by awemawson - 01-18-2016, 03:44 AM
RE: OnShape, a Free 3D CAD Program - by Mayhem - 01-18-2016, 05:19 AM
RE: OnShape, a Free 3D CAD Program - by Pete O - 01-18-2016, 07:29 AM
RE: OnShape, a Free 3D CAD Program - by wawoodman - 01-18-2016, 12:15 PM



Users browsing this thread: 6 Guest(s)