MetalworkingFun Forum › Machining › General Metalworking Discussion v
Setting Up KOC100 VFD

Thread Modes
Setting Up KOC100 VFD
Hawkeye Offline
Junior
****
Posts: 535
Threads: 39
Joined: Jan 2013
Location: Kelowna, BC, Canada
#21
01-01-2016, 12:14 AM
As it happens, d2-01 was set on 4.0. d2-02 was set on 30.0. I changed them both to 0, but no improvement. I'm only using one motor, so I didn't look at those entries.
Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.
Reply
Thanks given by:


Messages In This Thread
Setting Up KOC100 VFD - by Hawkeye - 12-28-2015, 11:16 PM
RE: Setting Up KOC100 VFD - by RobWilson - 12-29-2015, 03:15 AM
RE: Setting Up KOC100 VFD - by RobWilson - 12-29-2015, 01:19 PM
RE: Setting Up KOC100 VFD - by Highpower - 12-29-2015, 04:10 AM
RE: Setting Up KOC100 VFD - by EdK - 12-29-2015, 10:13 AM
RE: Setting Up KOC100 VFD - by Hawkeye - 12-29-2015, 12:09 PM
RE: Setting Up KOC100 VFD - by Highpower - 12-29-2015, 01:49 PM
RE: Setting Up KOC100 VFD - by wawoodman - 12-29-2015, 02:22 PM
RE: Setting Up KOC100 VFD - by Hawkeye - 12-29-2015, 09:10 PM
RE: Setting Up KOC100 VFD - by EdK - 12-29-2015, 09:38 PM
RE: Setting Up KOC100 VFD - by f350ca - 12-30-2015, 01:20 AM
RE: Setting Up KOC100 VFD - by Vinny - 12-30-2015, 02:16 AM
RE: Setting Up KOC100 VFD - by EdK - 12-30-2015, 10:08 AM
RE: Setting Up KOC100 VFD - by Highpower - 12-30-2015, 06:38 PM
RE: Setting Up KOC100 VFD - by Hawkeye - 12-31-2015, 12:51 AM
RE: Setting Up KOC100 VFD - by Highpower - 12-31-2015, 07:13 AM
RE: Setting Up KOC100 VFD - by EdK - 12-31-2015, 11:16 AM
RE: Setting Up KOC100 VFD - by Hawkeye - 12-31-2015, 11:22 AM
RE: Setting Up KOC100 VFD - by EdK - 12-31-2015, 12:05 PM
RE: Setting Up KOC100 VFD - by Highpower - 12-31-2015, 10:26 PM
RE: Setting Up KOC100 VFD - by Hawkeye - 01-01-2016, 12:14 AM
RE: Setting Up KOC100 VFD - by Highpower - 01-09-2016, 10:04 AM
RE: Setting Up KOC100 VFD - by Highpower - 01-01-2016, 06:24 AM
RE: Setting Up KOC100 VFD - by EdK - 01-01-2016, 09:31 AM
RE: Setting Up KOC100 VFD - by Highpower - 01-01-2016, 05:32 PM
RE: Setting Up KOC100 VFD - by EdK - 01-01-2016, 09:23 PM
RE: Setting Up KOC100 VFD - by Hawkeye - 01-01-2016, 09:27 PM
RE: Setting Up KOC100 VFD - by FernV - 01-09-2016, 03:19 AM
RE: Setting Up KOC100 VFD - by FernV - 01-09-2016, 11:42 AM
RE: Setting Up KOC100 VFD - by Hawkeye - 01-10-2016, 12:39 AM
RE: Setting Up KOC100 VFD - by 2w1USAF - 03-01-2016, 07:59 PM
RE: Setting Up KOC100 VFD - by Hawkeye - 03-02-2016, 12:13 AM



Users browsing this thread: 1 Guest(s)