Setting Up KOC100 VFD
#7
(12-29-2015, 12:09 PM)Hawkeye Wrote: The VFD is a KOC100-1R5S2 - rated at 1.5KW, single-phase, 220 Volt input, 7.0 amp output tracking input voltage.

Willie, read page 36. b0-30 is a test setting, not a parameter. The table only goes to -26.

OK, I have to be looking at the wrong manual then. I searched the whole .pdf and couldn't find "b0-30" on page 36 or anywhere in the entire manual for that matter.

Stupid question..... are you bench testing this motor (no load), or is it connected to a machine? And are you getting a trip indicator along with your err code?

I had the opposite problem with my Hitachi when I was setting it up on my lathe. Mine kept tripping on deceleration due to a buss over-voltage. I had the decel time set too short. Blush
Willie
Reply
Thanks given by:


Messages In This Thread
Setting Up KOC100 VFD - by Hawkeye - 12-28-2015, 11:16 PM
RE: Setting Up KOC100 VFD - by RobWilson - 12-29-2015, 03:15 AM
RE: Setting Up KOC100 VFD - by RobWilson - 12-29-2015, 01:19 PM
RE: Setting Up KOC100 VFD - by Highpower - 12-29-2015, 04:10 AM
RE: Setting Up KOC100 VFD - by EdK - 12-29-2015, 10:13 AM
RE: Setting Up KOC100 VFD - by Hawkeye - 12-29-2015, 12:09 PM
RE: Setting Up KOC100 VFD - by Highpower - 12-29-2015, 01:49 PM
RE: Setting Up KOC100 VFD - by wawoodman - 12-29-2015, 02:22 PM
RE: Setting Up KOC100 VFD - by Hawkeye - 12-29-2015, 09:10 PM
RE: Setting Up KOC100 VFD - by EdK - 12-29-2015, 09:38 PM
RE: Setting Up KOC100 VFD - by f350ca - 12-30-2015, 01:20 AM
RE: Setting Up KOC100 VFD - by Vinny - 12-30-2015, 02:16 AM
RE: Setting Up KOC100 VFD - by EdK - 12-30-2015, 10:08 AM
RE: Setting Up KOC100 VFD - by Highpower - 12-30-2015, 06:38 PM
RE: Setting Up KOC100 VFD - by Hawkeye - 12-31-2015, 12:51 AM
RE: Setting Up KOC100 VFD - by Highpower - 12-31-2015, 07:13 AM
RE: Setting Up KOC100 VFD - by EdK - 12-31-2015, 11:16 AM
RE: Setting Up KOC100 VFD - by Hawkeye - 12-31-2015, 11:22 AM
RE: Setting Up KOC100 VFD - by EdK - 12-31-2015, 12:05 PM
RE: Setting Up KOC100 VFD - by Highpower - 12-31-2015, 10:26 PM
RE: Setting Up KOC100 VFD - by Hawkeye - 01-01-2016, 12:14 AM
RE: Setting Up KOC100 VFD - by Highpower - 01-09-2016, 10:04 AM
RE: Setting Up KOC100 VFD - by Highpower - 01-01-2016, 06:24 AM
RE: Setting Up KOC100 VFD - by EdK - 01-01-2016, 09:31 AM
RE: Setting Up KOC100 VFD - by Highpower - 01-01-2016, 05:32 PM
RE: Setting Up KOC100 VFD - by EdK - 01-01-2016, 09:23 PM
RE: Setting Up KOC100 VFD - by Hawkeye - 01-01-2016, 09:27 PM
RE: Setting Up KOC100 VFD - by FernV - 01-09-2016, 03:19 AM
RE: Setting Up KOC100 VFD - by FernV - 01-09-2016, 11:42 AM
RE: Setting Up KOC100 VFD - by Hawkeye - 01-10-2016, 12:39 AM
RE: Setting Up KOC100 VFD - by 2w1USAF - 03-01-2016, 07:59 PM
RE: Setting Up KOC100 VFD - by Hawkeye - 03-02-2016, 12:13 AM



Users browsing this thread: 7 Guest(s)