|
Churchill CUB Lathe
|
10-18-2015, 04:15 PM
Another awesome job Rob, that lathe will be better than new. I always got the impression that Churchills were good lathes, is it just the Cub that was poor build quality, or do you just thing this one has been badly treated?
Phil
Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
|
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
Churchill CUB Lathe - by RobWilson - 10-18-2015, 09:36 AM
RE: Churchill CUB Lathe - by krv3000 - 10-18-2015, 10:04 AM
RE: Churchill CUB Lathe - by RobWilson - 10-18-2015, 10:07 AM
RE: Churchill CUB Lathe - by Mayhem - 10-18-2015, 10:40 AM
RE: Churchill CUB Lathe - by EdK - 10-18-2015, 11:13 AM
RE: Churchill CUB Lathe - by Highpower - 10-18-2015, 11:25 AM
RE: Churchill CUB Lathe - by RobWilson - 10-18-2015, 01:35 PM
RE: Churchill CUB Lathe - by Sunset Machine - 10-18-2015, 12:10 PM
RE: Churchill CUB Lathe - by RobWilson - 10-18-2015, 01:38 PM
RE: Churchill CUB Lathe - by wawoodman - 10-18-2015, 12:13 PM
RE: Churchill CUB Lathe - by Dr Stan - 10-18-2015, 02:50 PM
RE: Churchill CUB Lathe - by EdK - 10-18-2015, 03:58 PM
RE: Churchill CUB Lathe - by RobWilson - 10-19-2015, 09:47 AM
RE: Churchill CUB Lathe - by hermetic - 10-18-2015, 04:15 PM
RE: Churchill CUB Lathe - by RobWilson - 10-19-2015, 09:52 AM
RE: Churchill CUB Lathe - by EdK - 10-19-2015, 04:17 PM
RE: Churchill CUB Lathe - by Micktoon - 10-20-2015, 03:19 AM
RE: Churchill CUB Lathe - by RobWilson - 10-20-2015, 10:12 AM
RE: Churchill CUB Lathe - by krv3000 - 10-20-2015, 01:21 PM
RE: Churchill CUB Lathe - by doubleboost - 10-20-2015, 02:57 PM
RE: Churchill CUB Lathe - by RobWilson - 10-21-2015, 10:40 AM
RE: Churchill CUB Lathe - by RobWilson - 12-13-2015, 03:48 AM
RE: Churchill CUB Lathe - by hermetic - 12-13-2015, 06:15 AM
RE: Churchill CUB Lathe - by RobWilson - 12-13-2015, 07:27 AM
RE: Churchill CUB Lathe - by DaveH - 12-13-2015, 07:45 AM
RE: Churchill CUB Lathe - by RobWilson - 12-13-2015, 07:48 AM
RE: Churchill CUB Lathe - by Duane - 11-14-2020, 06:33 PM
RE: Churchill CUB Lathe - by Highpower - 11-15-2020, 02:23 AM
RE: Churchill CUB Lathe - by awemawson - 11-15-2020, 02:49 AM
RE: Churchill CUB Lathe - by Highpower - 11-15-2020, 11:24 AM
RE: Churchill CUB Lathe - by awemawson - 11-15-2020, 02:22 PM
RE: Churchill CUB Lathe - by Pete O - 11-15-2020, 06:12 PM
RE: Churchill CUB Lathe - by Vinny - 11-18-2020, 04:05 PM
|
