MetalworkingFun Forum › Machining › General Metalworking Discussion v
Churchill CUB Lathe

Thread Modes
Churchill CUB Lathe
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#12
10-18-2015, 03:58 PM
Rob,

Did you make the one piece gear using the shaper or the lathe? I can't tell by the picture but it looks like it's chucked up in the lathe, unless you have a fixture on your shaper for mounting the chuck. Chin

Ed
Reply
Thanks given by:


Messages In This Thread
Churchill CUB Lathe - by RobWilson - 10-18-2015, 09:36 AM
RE: Churchill CUB Lathe - by krv3000 - 10-18-2015, 10:04 AM
RE: Churchill CUB Lathe - by RobWilson - 10-18-2015, 10:07 AM
RE: Churchill CUB Lathe - by Mayhem - 10-18-2015, 10:40 AM
RE: Churchill CUB Lathe - by EdK - 10-18-2015, 11:13 AM
RE: Churchill CUB Lathe - by Highpower - 10-18-2015, 11:25 AM
RE: Churchill CUB Lathe - by RobWilson - 10-18-2015, 01:35 PM
RE: Churchill CUB Lathe - by Sunset Machine - 10-18-2015, 12:10 PM
RE: Churchill CUB Lathe - by RobWilson - 10-18-2015, 01:38 PM
RE: Churchill CUB Lathe - by wawoodman - 10-18-2015, 12:13 PM
RE: Churchill CUB Lathe - by Dr Stan - 10-18-2015, 02:50 PM
RE: Churchill CUB Lathe - by EdK - 10-18-2015, 03:58 PM
RE: Churchill CUB Lathe - by RobWilson - 10-19-2015, 09:47 AM
RE: Churchill CUB Lathe - by hermetic - 10-18-2015, 04:15 PM
RE: Churchill CUB Lathe - by RobWilson - 10-19-2015, 09:52 AM
RE: Churchill CUB Lathe - by EdK - 10-19-2015, 04:17 PM
RE: Churchill CUB Lathe - by Micktoon - 10-20-2015, 03:19 AM
RE: Churchill CUB Lathe - by RobWilson - 10-20-2015, 10:12 AM
RE: Churchill CUB Lathe - by krv3000 - 10-20-2015, 01:21 PM
RE: Churchill CUB Lathe - by doubleboost - 10-20-2015, 02:57 PM
RE: Churchill CUB Lathe - by RobWilson - 10-21-2015, 10:40 AM
RE: Churchill CUB Lathe - by RobWilson - 12-13-2015, 03:48 AM
RE: Churchill CUB Lathe - by hermetic - 12-13-2015, 06:15 AM
RE: Churchill CUB Lathe - by RobWilson - 12-13-2015, 07:27 AM
RE: Churchill CUB Lathe - by DaveH - 12-13-2015, 07:45 AM
RE: Churchill CUB Lathe - by RobWilson - 12-13-2015, 07:48 AM
RE: Churchill CUB Lathe - by Duane - 11-14-2020, 06:33 PM
RE: Churchill CUB Lathe - by Highpower - 11-15-2020, 02:23 AM
RE: Churchill CUB Lathe - by awemawson - 11-15-2020, 02:49 AM
RE: Churchill CUB Lathe - by Highpower - 11-15-2020, 11:24 AM
RE: Churchill CUB Lathe - by awemawson - 11-15-2020, 02:22 PM
RE: Churchill CUB Lathe - by Pete O - 11-15-2020, 06:12 PM
RE: Churchill CUB Lathe - by Vinny - 11-18-2020, 04:05 PM



Users browsing this thread: 3 Guest(s)