Boring heads for the mill
#5
I have a 2" boring head and it's done almost everything I've needed. I'll eventually get a 3" because there have been a couple of times where I could have used one. My 2" is the typical import with the dovetail/leadscrew setup. Smiley-gen163

Ed
Reply
Thanks given by:


Messages In This Thread
Boring heads for the mill - by DanH - 06-04-2012, 01:32 PM
RE: Boring heads for the mill - by doubleboost - 06-04-2012, 02:12 PM
RE: Boring heads for the mill - by Hopefuldave - 06-04-2012, 02:22 PM
RE: Boring heads for the mill - by DanH - 06-04-2012, 03:43 PM
RE: Boring heads for the mill - by EdK - 06-04-2012, 04:16 PM
RE: Boring heads for the mill - by f350ca - 06-04-2012, 05:23 PM
RE: Boring heads for the mill - by DaveH - 06-04-2012, 05:26 PM
RE: Boring heads for the mill - by EdK - 06-04-2012, 05:39 PM
RE: Boring heads for the mill - by DanH - 06-04-2012, 08:06 PM
RE: Boring heads for the mill - by ukazak - 06-05-2012, 01:45 AM
RE: Boring heads for the mill - by doubleboost - 06-05-2012, 05:10 AM
RE: Boring heads for the mill - by Mayhem - 06-05-2012, 06:24 AM
RE: Boring heads for the mill - by f350ca - 06-05-2012, 09:57 AM
RE: Boring heads for the mill - by Highpower - 06-05-2012, 03:45 PM
RE: Boring heads for the mill - by EdK - 06-05-2012, 03:59 PM
RE: Boring heads for the mill - by rleete - 06-05-2012, 06:56 PM
RE: Boring heads for the mill - by stevec - 06-05-2012, 07:18 PM
RE: Boring heads for the mill - by DanH - 06-05-2012, 07:28 PM
RE: Boring heads for the mill - by krv3000 - 06-06-2012, 05:05 AM
RE: Boring heads for the mill - by PixMan - 06-15-2012, 10:09 PM
RE: Boring heads for the mill - by TomG - 06-21-2012, 12:35 PM
RE: Boring heads for the mill - by DaveH - 06-21-2012, 01:43 PM
RE: Boring heads for the mill - by TomG - 06-21-2012, 02:21 PM
RE: Boring heads for the mill - by RobWilson - 06-21-2012, 02:45 PM
RE: Boring heads for the mill - by RobWilson - 06-21-2012, 01:56 PM
RE: Boring heads for the mill - by RobWilson - 06-21-2012, 03:02 PM
RE: Boring heads for the mill - by Keith_W - 06-22-2012, 03:33 PM
RE: Boring heads for the mill - by TomG - 06-22-2012, 05:34 PM
RE: Boring heads for the mill - by DaveH - 06-23-2012, 07:15 AM
RE: Boring heads for the mill - by PixMan - 06-22-2012, 07:10 PM
RE: Boring heads for the mill - by EdK - 06-22-2012, 07:16 PM
RE: Boring heads for the mill - by pineyfolks - 07-25-2012, 04:20 AM



Users browsing this thread: 4 Guest(s)