Cutting a blind keyway
#28
(09-19-2015, 08:46 AM)TomG Wrote: Pete,

Actually, four flute end mills are more rigid than two flutes.

I have access to a force gauge at work. It might be fun to see how much these end mills do deflect relative to each other.

Tom

Just when you think it is safe to go back into the water.....   Slaphead

I can provide a cross section of a 2-flute. Anybody else want to volunteer to do a 4-flute?   Rotfl

[Image: th_Half-inch_end_mill.jpg]
Willie
Reply
Thanks given by:


Messages In This Thread
Cutting a blind keyway - by Pete O - 09-11-2015, 04:02 AM
RE: Cutting a blind keyway - by RobWilson - 09-11-2015, 04:25 AM
RE: Cutting a blind keyway - by Pete O - 09-11-2015, 07:04 AM
RE: Cutting a blind keyway - by RobWilson - 09-11-2015, 09:03 AM
RE: Cutting a blind keyway - by RobWilson - 09-12-2015, 10:05 AM
RE: Cutting a blind keyway - by DaveH - 09-11-2015, 07:59 AM
RE: Cutting a blind keyway - by TomG - 09-11-2015, 07:31 PM
RE: Cutting a blind keyway - by PixMan - 09-11-2015, 07:57 PM
RE: Cutting a blind keyway - by EdK - 09-11-2015, 08:07 PM
RE: Cutting a blind keyway - by f350ca - 09-11-2015, 08:18 PM
RE: Cutting a blind keyway - by PixMan - 09-12-2015, 06:23 AM
RE: Cutting a blind keyway - by TomG - 09-12-2015, 09:52 AM
RE: Cutting a blind keyway - by mcostello - 09-12-2015, 12:10 PM
RE: Cutting a blind keyway - by Pete O - 09-16-2015, 08:00 PM
RE: Cutting a blind keyway - by Pete O - 09-18-2015, 04:35 AM
RE: Cutting a blind keyway - by Mayhem - 09-18-2015, 05:07 AM
RE: Cutting a blind keyway - by PixMan - 09-18-2015, 06:34 AM
RE: Cutting a blind keyway - by Mayhem - 09-18-2015, 06:44 AM
RE: Cutting a blind keyway - by Highpower - 09-18-2015, 07:42 AM
RE: Cutting a blind keyway - by EdK - 09-18-2015, 07:51 AM
RE: Cutting a blind keyway - by Highpower - 09-18-2015, 08:08 AM
RE: Cutting a blind keyway - by Pete O - 09-18-2015, 07:55 AM
RE: Cutting a blind keyway - by Highpower - 09-18-2015, 08:19 AM
RE: Cutting a blind keyway - by PixMan - 09-18-2015, 10:22 AM
RE: Cutting a blind keyway - by DaveH - 09-18-2015, 01:10 PM
RE: Cutting a blind keyway - by Vinny - 09-18-2015, 05:17 PM
RE: Cutting a blind keyway - by TomG - 09-19-2015, 08:46 AM
RE: Cutting a blind keyway - by Highpower - 09-19-2015, 10:31 AM
RE: Cutting a blind keyway - by Vinny - 09-19-2015, 04:03 PM



Users browsing this thread: 7 Guest(s)