Idea Making ready for new Mill /Lathe
#44
Took a Vacation  day off on Thur  spent a few Hours under my craw space playing  Electrician /Plummer/ construction guy ,found a nice sink hole had to address . O well half a day shot. came out like the swamp thing ...... Nice day to spend vacation day  under the house

However   All set now Power is in garage 220V singe phase   air lines are all hooked  ready to "Rock N Roll"  
Got shipping confirmation  for  this upcoming Tues on my new mill  PM 932 PDF . Maybe some Good news . So far it looks like the beer fridge is staying we will see when mill is in place


Attached Files Thumbnail(s)
       
Reply
Thanks given by:


Messages In This Thread
Making ready for new Mill /Lathe - by Kennyv - 07-13-2015, 09:11 AM
RE: Making ready for new Mill /Lathe - by Vinny - 07-13-2015, 04:13 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-15-2015, 10:55 PM
RE: Making ready for new Mill /Lathe - by stevec - 07-16-2015, 06:22 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-16-2015, 09:16 AM
RE: Making ready for new Mill /Lathe - by Vinny - 07-16-2015, 05:49 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-18-2015, 11:11 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-19-2015, 06:49 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-19-2015, 07:04 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-19-2015, 07:23 PM
RE: Making ready for new Mill /Lathe - by Mayhem - 07-20-2015, 05:59 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-20-2015, 09:06 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-19-2015, 11:32 PM
RE: Making ready for new Mill /Lathe - by stevec - 07-20-2015, 01:44 PM
RE: Making ready for new Mill /Lathe - by Dr Stan - 07-20-2015, 01:50 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-20-2015, 03:24 PM
RE: Making ready for new Mill /Lathe - by texx - 07-20-2015, 03:59 PM
RE: Making ready for new Mill /Lathe - by Pete O - 07-20-2015, 07:37 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-21-2015, 01:28 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-27-2015, 09:26 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-27-2015, 09:45 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-27-2015, 09:52 PM
RE: Making ready for new Mill /Lathe - by Mayhem - 07-28-2015, 05:35 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-28-2015, 09:29 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-30-2015, 10:47 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-31-2015, 07:03 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-31-2015, 09:48 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-31-2015, 11:35 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-01-2015, 12:52 AM
RE: Making ready for new Mill /Lathe - by Vinny - 08-01-2015, 01:40 AM
RE: Making ready for new Mill /Lathe - by EdK - 08-01-2015, 08:26 AM
RE: Making ready for new Mill /Lathe - by DaveH - 08-01-2015, 08:45 AM
RE: Making ready for new Mill /Lathe - by EdK - 08-01-2015, 09:31 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-01-2015, 02:27 PM
RE: Making ready for new Mill /Lathe - by EdK - 08-01-2015, 02:37 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-02-2015, 09:59 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-05-2015, 06:53 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-10-2015, 12:18 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-16-2015, 08:25 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-21-2015, 08:13 AM
RE: Making ready for new Mill /Lathe - by PixMan - 08-22-2015, 11:52 AM
RE: Making ready for new Mill /Lathe - by EdK - 08-22-2015, 01:48 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-24-2015, 02:06 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 09-12-2015, 04:24 PM
RE: Making ready for new Mill /Lathe - by RobWilson - 09-13-2015, 01:08 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 09-13-2015, 08:52 AM
RE: Making ready for new Mill /Lathe - by RobWilson - 09-15-2015, 12:41 PM
RE: Making ready for new Mill /Lathe - by RobWilson - 09-15-2015, 12:44 PM



Users browsing this thread: 8 Guest(s)