MetalworkingFun Forum › Machining › General Metalworking Discussion v
[IDEA] Making ready for new Mill /Lathe

Thread Modes
Idea Making ready for new Mill /Lathe
texx Away
Freshman
**
Posts: 37
Threads: 3
Joined: May 2014
Location: australia
#19
07-20-2015, 03:59 PM
its an endless chain or chain block hoist . a block and tackle is ropes and sheaves .the block part reffers to the sheave block or set of pullys a 2 and a 3 or whatever combination and the tackle reffers to the ropes

johno
texx, proud to be a member of MetalworkingFun Forum since May 2014.
Reply
Thanks given by:


Messages In This Thread
Making ready for new Mill /Lathe - by Kennyv - 07-13-2015, 09:11 AM
RE: Making ready for new Mill /Lathe - by Vinny - 07-13-2015, 04:13 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-15-2015, 10:55 PM
RE: Making ready for new Mill /Lathe - by stevec - 07-16-2015, 06:22 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-16-2015, 09:16 AM
RE: Making ready for new Mill /Lathe - by Vinny - 07-16-2015, 05:49 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-18-2015, 11:11 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-19-2015, 06:49 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-19-2015, 07:04 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-19-2015, 07:23 PM
RE: Making ready for new Mill /Lathe - by Mayhem - 07-20-2015, 05:59 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-20-2015, 09:06 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-19-2015, 11:32 PM
RE: Making ready for new Mill /Lathe - by stevec - 07-20-2015, 01:44 PM
RE: Making ready for new Mill /Lathe - by Dr Stan - 07-20-2015, 01:50 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-20-2015, 03:24 PM
RE: Making ready for new Mill /Lathe - by texx - 07-20-2015, 03:59 PM
RE: Making ready for new Mill /Lathe - by Pete O - 07-20-2015, 07:37 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-21-2015, 01:28 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-27-2015, 09:26 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-27-2015, 09:45 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-27-2015, 09:52 PM
RE: Making ready for new Mill /Lathe - by Mayhem - 07-28-2015, 05:35 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-28-2015, 09:29 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-30-2015, 10:47 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-31-2015, 07:03 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-31-2015, 09:48 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-31-2015, 11:35 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-01-2015, 12:52 AM
RE: Making ready for new Mill /Lathe - by Vinny - 08-01-2015, 01:40 AM
RE: Making ready for new Mill /Lathe - by EdK - 08-01-2015, 08:26 AM
RE: Making ready for new Mill /Lathe - by DaveH - 08-01-2015, 08:45 AM
RE: Making ready for new Mill /Lathe - by EdK - 08-01-2015, 09:31 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-01-2015, 02:27 PM
RE: Making ready for new Mill /Lathe - by EdK - 08-01-2015, 02:37 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-02-2015, 09:59 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-05-2015, 06:53 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-10-2015, 12:18 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-16-2015, 08:25 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-21-2015, 08:13 AM
RE: Making ready for new Mill /Lathe - by PixMan - 08-22-2015, 11:52 AM
RE: Making ready for new Mill /Lathe - by EdK - 08-22-2015, 01:48 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-24-2015, 02:06 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 09-12-2015, 04:24 PM
RE: Making ready for new Mill /Lathe - by RobWilson - 09-13-2015, 01:08 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 09-13-2015, 08:52 AM
RE: Making ready for new Mill /Lathe - by RobWilson - 09-15-2015, 12:41 PM
RE: Making ready for new Mill /Lathe - by RobWilson - 09-15-2015, 12:44 PM



Users browsing this thread: 15 Guest(s)