Idea Making ready for new Mill /Lathe
#13
Its an inexpensive  " cheapo"  lifting apparatus  beter than the rhoper hoist no? im a one man band so I had no choice I caved in and baught sumthin new .Well its a done deal  I hope its to all your approval ..like 90 deg here in Joisey .. ya know,  knowbody here says Joisey I have no clue where folks think we talk like that.
Im not a carp tender but got er done .. Worse part was tryen e to stuff 3 2x6,s up in the ceiling . I only have 2 trap doors and like  the angle of the dangle didn't cut it . tried every combo that beat the hec out of me.    had to take off a foot ..my buddy told me 3 2x6,s I wanted to choke em... .   .. Miller time now  

ok  Got My Pm 25Mv all banded up tonight  making  ready for bigger model  . Tomorrow is the big day  gona go check out that lathe ...   so without further adue here the pics and  if  its not up to snuff  welp that's my prob but thanks for caring ...I think work out fine the trailer is 4' wide  bout 5' to  end off wheels I got the columns 6' apart.   Imo driver in cranker up set er down done deal...


Attached Files Thumbnail(s)
                       
Reply
Thanks given by:


Messages In This Thread
Making ready for new Mill /Lathe - by Kennyv - 07-13-2015, 09:11 AM
RE: Making ready for new Mill /Lathe - by Vinny - 07-13-2015, 04:13 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-15-2015, 10:55 PM
RE: Making ready for new Mill /Lathe - by stevec - 07-16-2015, 06:22 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-16-2015, 09:16 AM
RE: Making ready for new Mill /Lathe - by Vinny - 07-16-2015, 05:49 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-18-2015, 11:11 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-19-2015, 06:49 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-19-2015, 07:04 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-19-2015, 07:23 PM
RE: Making ready for new Mill /Lathe - by Mayhem - 07-20-2015, 05:59 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-20-2015, 09:06 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-19-2015, 11:32 PM
RE: Making ready for new Mill /Lathe - by stevec - 07-20-2015, 01:44 PM
RE: Making ready for new Mill /Lathe - by Dr Stan - 07-20-2015, 01:50 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-20-2015, 03:24 PM
RE: Making ready for new Mill /Lathe - by texx - 07-20-2015, 03:59 PM
RE: Making ready for new Mill /Lathe - by Pete O - 07-20-2015, 07:37 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-21-2015, 01:28 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-27-2015, 09:26 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-27-2015, 09:45 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-27-2015, 09:52 PM
RE: Making ready for new Mill /Lathe - by Mayhem - 07-28-2015, 05:35 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-28-2015, 09:29 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-30-2015, 10:47 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-31-2015, 07:03 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 07-31-2015, 09:48 PM
RE: Making ready for new Mill /Lathe - by Vinny - 07-31-2015, 11:35 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-01-2015, 12:52 AM
RE: Making ready for new Mill /Lathe - by Vinny - 08-01-2015, 01:40 AM
RE: Making ready for new Mill /Lathe - by EdK - 08-01-2015, 08:26 AM
RE: Making ready for new Mill /Lathe - by DaveH - 08-01-2015, 08:45 AM
RE: Making ready for new Mill /Lathe - by EdK - 08-01-2015, 09:31 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-01-2015, 02:27 PM
RE: Making ready for new Mill /Lathe - by EdK - 08-01-2015, 02:37 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-02-2015, 09:59 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-05-2015, 06:53 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-10-2015, 12:18 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-16-2015, 08:25 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-21-2015, 08:13 AM
RE: Making ready for new Mill /Lathe - by PixMan - 08-22-2015, 11:52 AM
RE: Making ready for new Mill /Lathe - by EdK - 08-22-2015, 01:48 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 08-24-2015, 02:06 PM
RE: Making ready for new Mill /Lathe - by Kennyv - 09-12-2015, 04:24 PM
RE: Making ready for new Mill /Lathe - by RobWilson - 09-13-2015, 01:08 AM
RE: Making ready for new Mill /Lathe - by Kennyv - 09-13-2015, 08:52 AM
RE: Making ready for new Mill /Lathe - by RobWilson - 09-15-2015, 12:41 PM
RE: Making ready for new Mill /Lathe - by RobWilson - 09-15-2015, 12:44 PM



Users browsing this thread: 6 Guest(s)