What should be the allowance for press fitting?

Thread Modes

What should be the allowance for press fitting?

ukazak
Unregistered

05-29-2012, 04:03 PM

Dave,

not meant to screw it, Happyno

just tap the hole at the crank disk and press fit the shaft through the threads, instead of straight drilling 4mm.

Unal

« Next Oldest | Next Newest »

Messages In This Thread

What should be the allowance for press fitting? - by ukazak - 05-29-2012, 12:56 AM

RE: What should be the allowance for press fitting? - by PixMan - 05-29-2012, 06:10 AM

RE: What should be the allowance for press fitting? - by DaveH - 05-29-2012, 09:39 AM

RE: What should be the allowance for press fitting? - by ukazak - 05-29-2012, 12:37 PM

RE: What should be the allowance for press fitting? - by ScrapMetal - 05-29-2012, 09:33 PM

RE: What should be the allowance for press fitting? - by DaveH - 05-29-2012, 01:13 PM

RE: What should be the allowance for press fitting? - by ukazak - 05-29-2012, 03:09 PM

RE: What should be the allowance for press fitting? - by DaveH - 05-29-2012, 03:18 PM

RE: What should be the allowance for press fitting? - by ukazak - 05-29-2012, 04:03 PM

RE: What should be the allowance for press fitting? - by DaveH - 05-29-2012, 04:35 PM

RE: What should be the allowance for press fitting? - by DaveH - 05-29-2012, 04:47 PM

RE: What should be the allowance for press fitting? - by ukazak - 05-29-2012, 04:48 PM

RE: What should be the allowance for press fitting? - by ukazak - 05-29-2012, 05:05 PM

RE: What should be the allowance for press fitting? - by DaveH - 05-29-2012, 05:19 PM

RE: What should be the allowance for press fitting? - by EdK - 05-29-2012, 10:33 PM

RE: What should be the allowance for press fitting? - by Tony Wells - 05-30-2012, 01:16 AM

RE: What should be the allowance for press fitting? - by DaveH - 05-30-2012, 06:47 AM

RE: What should be the allowance for press fitting? - by Tony Wells - 05-30-2012, 07:44 AM

RE: What should be the allowance for press fitting? - by DaveH - 05-30-2012, 07:59 AM

RE: What should be the allowance for press fitting? - by ukazak - 05-30-2012, 11:19 AM

RE: What should be the allowance for press fitting? - by DaveH - 05-30-2012, 01:53 PM

RE: What should be the allowance for press fitting? - by ukazak - 05-31-2012, 12:46 PM

RE: What should be the allowance for press fitting? - by DaveH - 05-31-2012, 12:55 PM

RE: What should be the allowance for press fitting? - by doubleboost - 05-30-2012, 03:45 PM

RE: What should be the allowance for press fitting? - by ukazak - 05-30-2012, 04:50 PM

RE: What should be the allowance for press fitting? - by ScrapMetal - 05-30-2012, 06:42 PM

RE: What should be the allowance for press fitting? - by stevec - 05-31-2012, 05:53 AM

RE: What should be the allowance for press fitting? - by ukazak - 05-31-2012, 12:43 PM

RE: What should be the allowance for press fitting? - by stevec - 05-31-2012, 06:20 PM

RE: What should be the allowance for press fitting? - by ukazak - 06-01-2012, 03:11 AM

RE: What should be the allowance for press fitting? - by Mayhem - 05-31-2012, 10:07 PM

RE: What should be the allowance for press fitting? - by stevec - 06-01-2012, 07:24 AM

RE: What should be the allowance for press fitting? - by EdK - 06-01-2012, 08:48 AM

RE: What should be the allowance for press fitting? - by stevec - 06-01-2012, 05:13 PM

RE: What should be the allowance for press fitting? - by ukazak - 06-01-2012, 02:17 PM

RE: What should be the allowance for press fitting? - by EdK - 06-01-2012, 02:56 PM

RE: What should be the allowance for press fitting? - by ukazak - 06-01-2012, 03:57 PM

RE: What should be the allowance for press fitting? - by EdK - 06-01-2012, 05:42 PM

RE: What should be the allowance for press fitting? - by stevec - 06-01-2012, 05:46 PM

RE: What should be the allowance for press fitting? - by EdK - 06-01-2012, 05:48 PM

Users browsing this thread: 8 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me