Tooling question for RF-45 clone

Hello There, Guest! Register

Thread Modes

Tooling question for RF-45 clone

ETC57

Offline

Junior

Posts: 576
Threads: 18
Joined: Feb 2012
Location: Washington State USA

#4

05-21-2012, 07:11 PM

Dan,

I too would have to say 8", even on my small mill I find I almost never take it off!

Unless that is, I need the lathe. Rotfl

Rotfl

Slaphead

Jerry.

Popcorn

ETC57, proud to be a member of MetalworkingFun Forum since Feb 2012.

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Tooling question for RF-45 clone - by DanH - 05-21-2012, 04:20 PM

RE: Tooling question for RF-45 clone - by EdK - 05-21-2012, 06:18 PM

RE: Tooling question for RF-45 clone - by krv3000 - 05-21-2012, 06:19 PM

RE: Tooling question for RF-45 clone - by ETC57 - 05-21-2012, 07:11 PM

RE: Tooling question for RF-45 clone - by henryarnold - 05-21-2012, 10:39 PM

RE: Tooling question for RF-45 clone - by Hopefuldave - 05-22-2012, 02:05 PM

RE: Tooling question for RF-45 clone - by DanH - 05-22-2012, 11:00 AM

RE: Tooling question for RF-45 clone - by Highpower - 05-22-2012, 11:20 AM

RE: Tooling question for RF-45 clone - by EdK - 05-22-2012, 11:34 AM

RE: Tooling question for RF-45 clone - by DanH - 05-22-2012, 12:14 PM

RE: Tooling question for RF-45 clone - by Highpower - 05-22-2012, 04:32 PM

RE: Tooling question for RF-45 clone - by EdK - 05-22-2012, 04:38 PM

RE: Tooling question for RF-45 clone - by DanH - 05-22-2012, 04:49 PM

RE: Tooling question for RF-45 clone - by EdK - 05-22-2012, 05:09 PM

RE: Tooling question for RF-45 clone - by DanH - 05-22-2012, 06:12 PM

RE: Tooling question for RF-45 clone - by TOM REED - 05-22-2012, 06:31 PM

RE: Tooling question for RF-45 clone - by EdK - 05-22-2012, 07:20 PM

RE: Tooling question for RF-45 clone - by TOM REED - 05-22-2012, 07:31 PM

RE: Tooling question for RF-45 clone - by EdK - 05-23-2012, 08:05 AM

RE: Tooling question for RF-45 clone - by stevec - 05-23-2012, 08:03 AM

RE: Tooling question for RF-45 clone - by TOM REED - 05-23-2012, 11:16 PM

RE: Tooling question for RF-45 clone - by EdK - 05-24-2012, 07:07 AM

RE: Tooling question for RF-45 clone - by stevec - 05-24-2012, 06:31 AM

RE: Tooling question for RF-45 clone - by Mayhem - 05-25-2012, 01:11 AM

RE: Tooling question for RF-45 clone - by DanH - 05-25-2012, 10:15 AM

RE: Tooling question for RF-45 clone - by ETC57 - 05-25-2012, 11:06 AM

Users browsing this thread: 4 Guest(s)