How to Add a 3 Phase Motor and VFD to a 10x22 Lathe

Thread Modes

How to Add a 3 Phase Motor and VFD to a 10x22 Lathe

doubleboost Offline

Super Moderator

Posts: 1,459
Threads: 159
Joined: Feb 2012
Location: Northern England

#15

05-20-2012, 05:18 PM

(05-20-2012, 09:53 AM)DanH Wrote: Thanks for the info guys. I am so new at this, I hope my questions don't seem too ridicules.

Hi
Dan your questions are just what this forum is all about
This link shows my lathe (which was 3 phase when i bought it) screw cutting using a VFD speed controller
http://www.metalworkingfun.com/showthrea...74#pid4374
John

http://www.youtube.com/user/doubleboost

Like Post

« Next Oldest | Next Newest »

Messages In This Thread

How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by henryarnold - 05-19-2012, 09:56 AM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by EdK - 05-19-2012, 10:28 AM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by henryarnold - 05-19-2012, 08:48 PM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by EdK - 05-20-2012, 11:55 AM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by henryarnold - 05-20-2012, 04:24 PM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by DaveH - 05-19-2012, 10:34 AM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by henryarnold - 05-19-2012, 08:50 PM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by DanH - 05-19-2012, 11:13 PM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by Highpower - 05-20-2012, 12:18 AM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by EdK - 05-20-2012, 08:54 AM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by henryarnold - 05-20-2012, 11:53 AM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by DanH - 05-20-2012, 09:53 AM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by EdK - 05-20-2012, 10:33 AM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by Highpower - 05-20-2012, 04:10 PM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by EdK - 05-20-2012, 06:14 PM

RE: How to Add a 3 Phase Motor and VFD to a 10x22 Lathe - by Highpower - 05-20-2012, 08:46 PM

Users browsing this thread: 3 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me