MetalworkingFun Forum › Machining › General Metalworking Discussion v
Material suggestions?

Thread Modes
Material suggestions?
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
The following 1 user Likes dallen's post:
Mayhem (04-03-2015)
#29
04-03-2015, 08:46 AM
use the 3/8 inch broach to cut the keyway in the ratchet, then make a T shaped key to fit both the pinon and ratchet, I seriously doubt that you will be able to shear the key by pulling on the handle.
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:


Messages In This Thread
Material suggestions? - by Highpower - 03-31-2015, 10:35 PM
RE: Material suggestions? - by Dr Stan - 03-31-2015, 10:48 PM
RE: Material suggestions? - by Highpower - 03-31-2015, 11:46 PM
RE: Material suggestions? - by PixMan - 03-31-2015, 10:53 PM
RE: Material suggestions? - by f350ca - 03-31-2015, 11:38 PM
RE: Material suggestions? - by Highpower - 03-31-2015, 11:50 PM
RE: Material suggestions? - by Highpower - 04-01-2015, 03:38 PM
RE: Material suggestions? - by dallen - 04-01-2015, 03:53 PM
RE: Material suggestions? - by Highpower - 04-01-2015, 04:20 PM
RE: Material suggestions? - by Vinny - 04-01-2015, 05:27 PM
RE: Material suggestions? - by Roadracer_Al - 04-01-2015, 06:10 PM
RE: Material suggestions? - by PixMan - 04-01-2015, 06:16 PM
RE: Material suggestions? - by EdK - 04-01-2015, 06:54 PM
RE: Material suggestions? - by Highpower - 04-01-2015, 08:55 PM
RE: Material suggestions? - by Dr Stan - 04-01-2015, 08:14 PM
RE: Material suggestions? - by PixMan - 04-02-2015, 05:59 AM
RE: Material suggestions? - by Highpower - 04-02-2015, 11:12 AM
RE: Material suggestions? - by f350ca - 04-02-2015, 08:55 AM
RE: Material suggestions? - by Highpower - 04-02-2015, 11:15 AM
RE: Material suggestions? - by dallen - 04-02-2015, 11:35 AM
RE: Material suggestions? - by Highpower - 04-02-2015, 12:45 PM
RE: Material suggestions? - by dallen - 04-02-2015, 12:55 PM
RE: Material suggestions? - by Highpower - 04-02-2015, 05:59 PM
RE: Material suggestions? - by dallen - 04-02-2015, 06:24 PM
RE: Material suggestions? - by Highpower - 04-02-2015, 09:40 PM
RE: Material suggestions? - by f350ca - 04-02-2015, 10:54 PM
RE: Material suggestions? - by Mayhem - 04-02-2015, 11:24 PM
RE: Material suggestions? - by Highpower - 04-02-2015, 11:48 PM
RE: Material suggestions? - by dallen - 04-03-2015, 08:46 AM
RE: Material suggestions? - by Highpower - 04-03-2015, 10:58 AM
RE: Material suggestions? - by stevec - 04-03-2015, 12:52 PM
RE: Material suggestions? - by f350ca - 04-03-2015, 12:54 PM
RE: Material suggestions? - by Highpower - 04-03-2015, 01:33 PM
RE: Material suggestions? - by dallen - 04-03-2015, 01:37 PM



Users browsing this thread: 3 Guest(s)