MetalworkingFun Forum › Machining › General Metalworking Discussion v
Material suggestions?

Thread Modes
Material suggestions?
Highpower Offline
JAFO
******
Posts: 4,460
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
#19
04-02-2015, 11:15 AM
(04-02-2015, 08:55 AM)f350ca Wrote: Ken is going to tear me apart for this suggestion but one of these will remove a lot of tough material pretty economically.


Takes inserts that I can get cheap even up here.

Excellent point Greg. If you can't find inserts, all you have is an expensive paperweight.
Willie
Reply
Thanks given by:


Messages In This Thread
Material suggestions? - by Highpower - 03-31-2015, 10:35 PM
RE: Material suggestions? - by Dr Stan - 03-31-2015, 10:48 PM
RE: Material suggestions? - by Highpower - 03-31-2015, 11:46 PM
RE: Material suggestions? - by PixMan - 03-31-2015, 10:53 PM
RE: Material suggestions? - by f350ca - 03-31-2015, 11:38 PM
RE: Material suggestions? - by Highpower - 03-31-2015, 11:50 PM
RE: Material suggestions? - by Highpower - 04-01-2015, 03:38 PM
RE: Material suggestions? - by dallen - 04-01-2015, 03:53 PM
RE: Material suggestions? - by Highpower - 04-01-2015, 04:20 PM
RE: Material suggestions? - by Vinny - 04-01-2015, 05:27 PM
RE: Material suggestions? - by Roadracer_Al - 04-01-2015, 06:10 PM
RE: Material suggestions? - by PixMan - 04-01-2015, 06:16 PM
RE: Material suggestions? - by EdK - 04-01-2015, 06:54 PM
RE: Material suggestions? - by Highpower - 04-01-2015, 08:55 PM
RE: Material suggestions? - by Dr Stan - 04-01-2015, 08:14 PM
RE: Material suggestions? - by PixMan - 04-02-2015, 05:59 AM
RE: Material suggestions? - by Highpower - 04-02-2015, 11:12 AM
RE: Material suggestions? - by f350ca - 04-02-2015, 08:55 AM
RE: Material suggestions? - by Highpower - 04-02-2015, 11:15 AM
RE: Material suggestions? - by dallen - 04-02-2015, 11:35 AM
RE: Material suggestions? - by Highpower - 04-02-2015, 12:45 PM
RE: Material suggestions? - by dallen - 04-02-2015, 12:55 PM
RE: Material suggestions? - by Highpower - 04-02-2015, 05:59 PM
RE: Material suggestions? - by dallen - 04-02-2015, 06:24 PM
RE: Material suggestions? - by Highpower - 04-02-2015, 09:40 PM
RE: Material suggestions? - by f350ca - 04-02-2015, 10:54 PM
RE: Material suggestions? - by Mayhem - 04-02-2015, 11:24 PM
RE: Material suggestions? - by Highpower - 04-02-2015, 11:48 PM
RE: Material suggestions? - by dallen - 04-03-2015, 08:46 AM
RE: Material suggestions? - by Highpower - 04-03-2015, 10:58 AM
RE: Material suggestions? - by stevec - 04-03-2015, 12:52 PM
RE: Material suggestions? - by f350ca - 04-03-2015, 12:54 PM
RE: Material suggestions? - by Highpower - 04-03-2015, 01:33 PM
RE: Material suggestions? - by dallen - 04-03-2015, 01:37 PM



Users browsing this thread: 4 Guest(s)