Power tapping test results

Hello There, Guest! Register

Thread Modes

Power tapping test results

PixMan Offline

Offline

Resident Pariah

Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA

The following 1 user Likes PixMan's post:
Mayhem (03-30-2015)

#16

03-30-2015, 10:28 AM

(03-30-2015, 08:54 AM)DaveH Wrote: Ken,
Nice video

Ken, if you reduced the depth of cut to say .020" or .010" would you keep the spindle speed and the feed rate as it was?

DaveH

Actually I did make a finish pass at .015" deep but didn't change speed or feed, which I should have done. You can see in the later photos of the opened hole that the shiny, reflective finish seen in the video is gone and that's why.

I should have upped the spindle speed from 730 rpm to at least 1000 for that to get some heat back into the process.

Reply

Thanks given by: DaveH , EdK , stevec

« Next Oldest | Next Newest »

Messages In This Thread

Power tapping test results - by PixMan - 03-28-2015, 05:51 PM

RE: Power tapping test results - by EdK - 03-28-2015, 06:12 PM

RE: Power tapping test results - by PixMan - 03-28-2015, 06:26 PM

RE: Power tapping test results - by EdK - 03-28-2015, 06:43 PM

RE: Power tapping test results - by PixMan - 03-29-2015, 08:03 AM

RE: Power tapping test results - by Highpower - 03-29-2015, 11:04 AM

RE: Power tapping test results - by PixMan - 03-29-2015, 11:24 AM

RE: Power tapping test results - by Highpower - 03-29-2015, 12:11 PM

RE: Power tapping test results - by PixMan - 03-29-2015, 04:12 PM

RE: Power tapping test results - by PixMan - 03-29-2015, 05:44 PM

RE: Power tapping test results - by Mayhem - 03-30-2015, 06:03 AM

RE: Power tapping test results - by PixMan - 03-30-2015, 06:26 AM

RE: Power tapping test results - by EdK - 03-30-2015, 06:35 AM

RE: Power tapping test results - by PixMan - 03-30-2015, 07:12 AM

RE: Power tapping test results - by DaveH - 03-30-2015, 08:54 AM

RE: Power tapping test results - by PixMan - 03-30-2015, 10:28 AM

RE: Power tapping test results - by Mayhem - 04-05-2015, 10:33 AM

RE: Power tapping test results - by PixMan - 04-05-2015, 07:45 PM

RE: Power tapping test results - by Vinny - 04-05-2015, 08:06 PM

RE: Power tapping test results - by PixMan - 04-05-2015, 09:28 PM

RE: Power tapping test results - by Vinny - 04-05-2015, 10:07 PM

RE: Power tapping test results - by Mayhem - 04-06-2015, 04:31 AM

RE: Power tapping test results - by Vinny - 04-06-2015, 04:10 PM

RE: Power tapping test results - by f350ca - 04-06-2015, 04:46 PM

RE: Power tapping test results - by EdK - 04-06-2015, 05:42 PM

RE: Power tapping test results - by PixMan - 04-06-2015, 07:39 PM

RE: Power tapping test results - by Vinny - 04-06-2015, 09:06 PM

RE: Power tapping test results - by Dr Stan - 04-06-2015, 10:34 PM

RE: Power tapping test results - by f350ca - 04-06-2015, 10:21 PM

RE: Power tapping test results - by Vinny - 04-06-2015, 10:32 PM

RE: Power tapping test results - by Highpower - 04-06-2015, 11:29 PM

RE: Power tapping test results - by Mayhem - 04-07-2015, 07:40 AM

RE: Power tapping test results - by Highpower - 04-07-2015, 08:38 AM

RE: Power tapping test results - by Mayhem - 04-07-2015, 10:03 AM

Users browsing this thread: 1 Guest(s)