MetalworkingFun Forum › Machining › General Metalworking Discussion v
What face mill do u use???

Thread Modes
What face mill do u use???
aRM Offline
Sophmore
***
Posts: 214
Threads: 19
Joined: Oct 2014
Location: SOUTH AFRICA,KZN,DURBAN
#66
03-24-2015, 12:21 AM
(03-22-2015, 02:08 PM)PixMan Wrote: I just noticed your clamping of the work, or lack of it. Look into some Mitee-Bite or Talon Grip type of low profile toe clamps for that "free end" of the plate. Vibration kills carbide, you want that end to be securely fastened to the table.
Thanks Ken
The pic does not show the 4 huge clamps further back
However, looking at those Mitee-Bite's, they are exactly what the good doctor ordered, as we were earlier also contemplating fabricating something smaller to hold the face/beginning of our work pieces.
Only hope we can get these for our Mill Table, which we think is pretty standard Bridgeport sized.
Once again "Muchas Gracias, Maestro"
aRM
Reply
Thanks given by:


Messages In This Thread
What face mill do u use??? - by aRM - 03-08-2015, 04:03 PM
RE: WHAT FACEMILL DO U USE ??? - by EdK - 03-08-2015, 04:18 PM
RE: WHAT FACEMILL DO U USE ??? - by aRM - 03-08-2015, 04:45 PM
RE: WHAT FACEMILL DO U USE ??? - by stevec - 03-08-2015, 05:20 PM
RE: WHAT FACEMILL DO U USE ??? - by PixMan - 03-08-2015, 06:26 PM
RE: What face mill do u use??? - by stevec - 03-08-2015, 06:51 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 06:59 PM
RE: What face mill do u use??? - by stevec - 03-08-2015, 07:11 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 07:21 PM
RE: What face mill do u use??? - by mike-sid - 03-08-2015, 08:21 PM
RE: What face mill do u use??? - by Highpower - 03-08-2015, 08:32 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 09:52 PM
RE: What face mill do u use??? - by mike-sid - 03-08-2015, 10:21 PM
RE: What face mill do u use??? - by Highpower - 03-08-2015, 11:47 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 10:32 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 06:46 AM
RE: What face mill do u use??? - by Highpower - 03-09-2015, 10:06 AM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 11:31 AM
RE: What face mill do u use??? - by EdK - 03-09-2015, 12:02 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:19 PM
RE: What face mill do u use??? - by EdK - 03-09-2015, 12:26 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 12:40 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:42 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 12:48 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:56 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:52 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 01:36 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 01:53 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 02:32 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 01:56 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 02:53 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 10:55 PM
RE: What face mill do u use??? - by aRM - 03-10-2015, 12:30 AM
RE: What face mill do u use??? - by aRM - 03-13-2015, 02:33 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 06:07 PM
RE: What face mill do u use??? - by aRM - 03-10-2015, 12:05 AM
RE: What face mill do u use??? - by Mayhem - 03-10-2015, 05:44 AM
RE: What face mill do u use??? - by PixMan - 03-10-2015, 07:45 AM
RE: What face mill do u use??? - by aRM - 03-11-2015, 12:47 PM
RE: What face mill do u use??? - by PixMan - 03-11-2015, 04:22 PM
RE: What face mill do u use??? - by aRM - 03-13-2015, 03:24 PM
RE: What face mill do u use??? - by PixMan - 03-11-2015, 09:27 PM
RE: What face mill do u use??? - by DaveH - 03-13-2015, 03:50 PM
RE: What face mill do u use??? - by PixMan - 03-13-2015, 07:22 PM
RE: What face mill do u use??? - by aRM - 03-18-2015, 02:59 PM
RE: What face mill do u use??? - by DaveH - 03-18-2015, 03:16 PM
RE: What face mill do u use??? - by aRM - 03-19-2015, 01:31 PM
RE: What face mill do u use??? - by DaveH - 03-18-2015, 03:49 PM
RE: What face mill do u use??? - by aRM - 03-19-2015, 01:43 PM
RE: What face mill do u use??? - by Vinny - 03-18-2015, 04:45 PM
RE: What face mill do u use??? - by DaveH - 03-18-2015, 05:15 PM
RE: What face mill do u use??? - by PixMan - 03-18-2015, 05:41 PM
RE: What face mill do u use??? - by aRM - 03-19-2015, 02:01 PM
RE: What face mill do u use??? - by DaveH - 03-19-2015, 03:24 PM
RE: What face mill do u use??? - by aRM - 03-20-2015, 02:19 PM
RE: What face mill do u use??? - by PixMan - 03-19-2015, 07:02 PM
RE: What face mill do u use??? - by aRM - 03-20-2015, 02:33 PM
RE: What face mill do u use??? - by DaveH - 03-20-2015, 02:56 PM
RE: What face mill do u use??? - by aRM - 03-22-2015, 12:00 PM
RE: What face mill do u use??? - by PixMan - 03-20-2015, 04:28 PM
RE: What face mill do u use??? - by aRM - 03-22-2015, 12:31 PM
RE: What face mill do u use??? - by DaveH - 03-22-2015, 01:36 PM
RE: What face mill do u use??? - by aRM - 03-24-2015, 12:12 AM
RE: What face mill do u use??? - by Mayhem - 03-24-2015, 05:49 AM
RE: What face mill do u use??? - by aRM - 03-24-2015, 01:49 PM
RE: What face mill do u use??? - by PixMan - 03-22-2015, 01:46 PM
RE: What face mill do u use??? - by aRM - 03-24-2015, 02:28 PM
RE: What face mill do u use??? - by PixMan - 03-22-2015, 02:08 PM
RE: What face mill do u use??? - by aRM - 03-24-2015, 12:21 AM
RE: What face mill do u use??? - by PixMan - 03-24-2015, 10:38 PM
RE: What face mill do u use??? - by aRM - 03-25-2015, 12:07 AM



Users browsing this thread: 6 Guest(s)