MetalworkingFun Forum › Machining › General Metalworking Discussion v
What face mill do u use???

Thread Modes
What face mill do u use???
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#7
03-08-2015, 06:59 PM
(03-08-2015, 06:51 PM)stevec Wrote:
(03-08-2015, 06:26 PM)PixMan Wrote: So it took (effectively) 7.5 inserts per part.
Ken, did you mean 7.5 "passes" per part?
Or am I (as usual) "out to lunch"?

Steve

Smiley-eatdrink004

No, Steve, I meant what I wrote. The cutter takes 5 inserts, each has two edges. By the time one part is done (six 3mm deep passes, 3 each side), both edges of one set of five inserts are toast, plus ONE edge of the second set of five.

Make sense?
Reply
Thanks given by:


Messages In This Thread
What face mill do u use??? - by aRM - 03-08-2015, 04:03 PM
RE: WHAT FACEMILL DO U USE ??? - by EdK - 03-08-2015, 04:18 PM
RE: WHAT FACEMILL DO U USE ??? - by aRM - 03-08-2015, 04:45 PM
RE: WHAT FACEMILL DO U USE ??? - by stevec - 03-08-2015, 05:20 PM
RE: WHAT FACEMILL DO U USE ??? - by PixMan - 03-08-2015, 06:26 PM
RE: What face mill do u use??? - by stevec - 03-08-2015, 06:51 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 06:59 PM
RE: What face mill do u use??? - by stevec - 03-08-2015, 07:11 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 07:21 PM
RE: What face mill do u use??? - by mike-sid - 03-08-2015, 08:21 PM
RE: What face mill do u use??? - by Highpower - 03-08-2015, 08:32 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 09:52 PM
RE: What face mill do u use??? - by mike-sid - 03-08-2015, 10:21 PM
RE: What face mill do u use??? - by Highpower - 03-08-2015, 11:47 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 10:32 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 06:46 AM
RE: What face mill do u use??? - by Highpower - 03-09-2015, 10:06 AM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 11:31 AM
RE: What face mill do u use??? - by EdK - 03-09-2015, 12:02 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:19 PM
RE: What face mill do u use??? - by EdK - 03-09-2015, 12:26 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 12:40 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:42 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 12:48 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:56 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:52 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 01:36 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 01:53 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 02:32 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 01:56 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 02:53 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 10:55 PM
RE: What face mill do u use??? - by aRM - 03-10-2015, 12:30 AM
RE: What face mill do u use??? - by aRM - 03-13-2015, 02:33 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 06:07 PM
RE: What face mill do u use??? - by aRM - 03-10-2015, 12:05 AM
RE: What face mill do u use??? - by Mayhem - 03-10-2015, 05:44 AM
RE: What face mill do u use??? - by PixMan - 03-10-2015, 07:45 AM
RE: What face mill do u use??? - by aRM - 03-11-2015, 12:47 PM
RE: What face mill do u use??? - by PixMan - 03-11-2015, 04:22 PM
RE: What face mill do u use??? - by aRM - 03-13-2015, 03:24 PM
RE: What face mill do u use??? - by PixMan - 03-11-2015, 09:27 PM
RE: What face mill do u use??? - by DaveH - 03-13-2015, 03:50 PM
RE: What face mill do u use??? - by PixMan - 03-13-2015, 07:22 PM
RE: What face mill do u use??? - by aRM - 03-18-2015, 02:59 PM
RE: What face mill do u use??? - by DaveH - 03-18-2015, 03:16 PM
RE: What face mill do u use??? - by aRM - 03-19-2015, 01:31 PM
RE: What face mill do u use??? - by DaveH - 03-18-2015, 03:49 PM
RE: What face mill do u use??? - by aRM - 03-19-2015, 01:43 PM
RE: What face mill do u use??? - by Vinny - 03-18-2015, 04:45 PM
RE: What face mill do u use??? - by DaveH - 03-18-2015, 05:15 PM
RE: What face mill do u use??? - by PixMan - 03-18-2015, 05:41 PM
RE: What face mill do u use??? - by aRM - 03-19-2015, 02:01 PM
RE: What face mill do u use??? - by DaveH - 03-19-2015, 03:24 PM
RE: What face mill do u use??? - by aRM - 03-20-2015, 02:19 PM
RE: What face mill do u use??? - by PixMan - 03-19-2015, 07:02 PM
RE: What face mill do u use??? - by aRM - 03-20-2015, 02:33 PM
RE: What face mill do u use??? - by DaveH - 03-20-2015, 02:56 PM
RE: What face mill do u use??? - by aRM - 03-22-2015, 12:00 PM
RE: What face mill do u use??? - by PixMan - 03-20-2015, 04:28 PM
RE: What face mill do u use??? - by aRM - 03-22-2015, 12:31 PM
RE: What face mill do u use??? - by DaveH - 03-22-2015, 01:36 PM
RE: What face mill do u use??? - by aRM - 03-24-2015, 12:12 AM
RE: What face mill do u use??? - by Mayhem - 03-24-2015, 05:49 AM
RE: What face mill do u use??? - by aRM - 03-24-2015, 01:49 PM
RE: What face mill do u use??? - by PixMan - 03-22-2015, 01:46 PM
RE: What face mill do u use??? - by aRM - 03-24-2015, 02:28 PM
RE: What face mill do u use??? - by PixMan - 03-22-2015, 02:08 PM
RE: What face mill do u use??? - by aRM - 03-24-2015, 12:21 AM
RE: What face mill do u use??? - by PixMan - 03-24-2015, 10:38 PM
RE: What face mill do u use??? - by aRM - 03-25-2015, 12:07 AM



Users browsing this thread: 6 Guest(s)