MetalworkingFun Forum › Machinery › Lathes v
[HELP] Edgewick Light Type Lathe help

Thread Modes
Help Edgewick Light Type Lathe help
terrywerm Offline
Sophmore
***
Posts: 60
Threads: 6
Joined: Nov 2013
Location: Jordan, MN
#23
01-26-2015, 01:51 AM (This post was last modified: 01-26-2015, 01:52 AM by terrywerm.)
Dan, did you ever figure out if the sliding gear is the one sticking out the left side of the machine?  The one I am talking about is just visible in the photo below, and is circled in red. Try pulling out on it.

   
[Image: coffee2.gif]


Terry
Making stuff with old machines.
Reply
Thanks given by: Dan Boy


Messages In This Thread
Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 04:11 AM
RE: Edgewick Light Type Lathe help - by tekfab - 01-25-2015, 05:21 AM
RE: Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 07:21 AM
RE: Edgewick Light Type Lathe help - by tekfab - 01-25-2015, 08:02 AM
RE: Edgewick Light Type Lathe help - by stevec - 01-25-2015, 09:01 AM
RE: Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 09:30 AM
RE: Edgewick Light Type Lathe help - by EdK - 01-25-2015, 09:39 AM
RE: Edgewick Light Type Lathe help - by terrywerm - 01-25-2015, 10:09 AM
RE: Edgewick Light Type Lathe help - by stevec - 01-25-2015, 07:45 PM
RE: Edgewick Light Type Lathe help - by tekfab - 01-25-2015, 10:27 AM
RE: Edgewick Light Type Lathe help - by Dr Stan - 01-25-2015, 10:29 AM
RE: Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 03:17 PM
RE: Edgewick Light Type Lathe help - by DaveH - 01-25-2015, 03:55 PM
RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:00 PM
RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:04 PM
RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:13 PM
RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:38 PM
RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:50 PM
RE: Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 05:06 PM
RE: Edgewick Light Type Lathe help - by Mayhem - 01-25-2015, 07:48 PM
RE: Edgewick Light Type Lathe help - by terrywerm - 01-26-2015, 01:51 AM
RE: Edgewick Light Type Lathe help - by Dan Boy - 01-26-2015, 01:58 AM
RE: Edgewick Light Type Lathe help - by terrywerm - 01-26-2015, 07:36 AM
RE: Edgewick Light Type Lathe help - by tekfab - 01-26-2015, 07:46 AM
RE: Edgewick Light Type Lathe help - by hermetic - 01-26-2015, 02:52 PM



Users browsing this thread: 4 Guest(s)