MetalworkingFun Forum › Machinery › Lathes v
[HELP] Edgewick Light Type Lathe help

Thread Modes
Help Edgewick Light Type Lathe help
hermetic Offline
Junior
****
Posts: 332
Threads: 10
Joined: Nov 2012
Location: East Yorkshire
#18
01-25-2015, 04:38 PM
Hi Again Dan,
This is an early conehead plain bearing lathe, I guess there is a flat belt and different sized pulleys under the round cover on the headstock, trying to find some pics of it, no luck so far. Where are you in the UK?
Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
Reply
Thanks given by:


Messages In This Thread
Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 04:11 AM
RE: Edgewick Light Type Lathe help - by tekfab - 01-25-2015, 05:21 AM
RE: Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 07:21 AM
RE: Edgewick Light Type Lathe help - by tekfab - 01-25-2015, 08:02 AM
RE: Edgewick Light Type Lathe help - by stevec - 01-25-2015, 09:01 AM
RE: Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 09:30 AM
RE: Edgewick Light Type Lathe help - by EdK - 01-25-2015, 09:39 AM
RE: Edgewick Light Type Lathe help - by terrywerm - 01-25-2015, 10:09 AM
RE: Edgewick Light Type Lathe help - by stevec - 01-25-2015, 07:45 PM
RE: Edgewick Light Type Lathe help - by tekfab - 01-25-2015, 10:27 AM
RE: Edgewick Light Type Lathe help - by Dr Stan - 01-25-2015, 10:29 AM
RE: Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 03:17 PM
RE: Edgewick Light Type Lathe help - by DaveH - 01-25-2015, 03:55 PM
RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:00 PM
RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:04 PM
RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:13 PM
RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:38 PM
RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:50 PM
RE: Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 05:06 PM
RE: Edgewick Light Type Lathe help - by Mayhem - 01-25-2015, 07:48 PM
RE: Edgewick Light Type Lathe help - by terrywerm - 01-26-2015, 01:51 AM
RE: Edgewick Light Type Lathe help - by Dan Boy - 01-26-2015, 01:58 AM
RE: Edgewick Light Type Lathe help - by terrywerm - 01-26-2015, 07:36 AM
RE: Edgewick Light Type Lathe help - by tekfab - 01-26-2015, 07:46 AM
RE: Edgewick Light Type Lathe help - by hermetic - 01-26-2015, 02:52 PM



Users browsing this thread: 2 Guest(s)