Edgewick Light Type Lathe help

Hello There, Guest! Register

Thread Modes

Help Edgewick Light Type Lathe help

Dan Boy Offline

Offline

Sophmore

Posts: 59
Threads: 14
Joined: Jan 2015
Location: UK

#13

01-25-2015, 03:17 PM (This post was last modified: 01-25-2015, 03:18 PM by Dan Boy.)

So I did a copuple of vids so you can see the problem better. Clearly I need to find the sliding gears though.

Cheers, Dan

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 04:11 AM

RE: Edgewick Light Type Lathe help - by tekfab - 01-25-2015, 05:21 AM

RE: Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 07:21 AM

RE: Edgewick Light Type Lathe help - by tekfab - 01-25-2015, 08:02 AM

RE: Edgewick Light Type Lathe help - by stevec - 01-25-2015, 09:01 AM

RE: Edgewick Light Type Lathe help - by Sunset Machine - 01-25-2015, 09:20 AM

RE: Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 09:30 AM

RE: Edgewick Light Type Lathe help - by EdK - 01-25-2015, 09:39 AM

RE: Edgewick Light Type Lathe help - by Sunset Machine - 01-25-2015, 09:42 AM

RE: Edgewick Light Type Lathe help - by terrywerm - 01-25-2015, 10:09 AM

RE: Edgewick Light Type Lathe help - by stevec - 01-25-2015, 07:45 PM

RE: Edgewick Light Type Lathe help - by tekfab - 01-25-2015, 10:27 AM

RE: Edgewick Light Type Lathe help - by Dr Stan - 01-25-2015, 10:29 AM

RE: Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 03:17 PM

RE: Edgewick Light Type Lathe help - by DaveH - 01-25-2015, 03:55 PM

RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:00 PM

RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:04 PM

RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:13 PM

RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:38 PM

RE: Edgewick Light Type Lathe help - by hermetic - 01-25-2015, 04:50 PM

RE: Edgewick Light Type Lathe help - by Dan Boy - 01-25-2015, 05:06 PM

RE: Edgewick Light Type Lathe help - by Mayhem - 01-25-2015, 07:48 PM

RE: Edgewick Light Type Lathe help - by terrywerm - 01-26-2015, 01:51 AM

RE: Edgewick Light Type Lathe help - by Dan Boy - 01-26-2015, 01:58 AM

RE: Edgewick Light Type Lathe help - by terrywerm - 01-26-2015, 07:36 AM

RE: Edgewick Light Type Lathe help - by tekfab - 01-26-2015, 07:46 AM

RE: Edgewick Light Type Lathe help - by hermetic - 01-26-2015, 02:52 PM

Users browsing this thread: 3 Guest(s)