MetalworkingFun Forum › Machining › General Metalworking Discussion v
help with angle iron's

Thread Modes
help with angle iron's
dbreeze225 Offline
Freshman
**
Posts: 19
Threads: 2
Joined: Jan 2015
Location: New York
#3
01-10-2015, 08:06 PM
yes each leg is 3/4in i tried on a lil test peice to try and polish it with various attachments for a dremel tool but like i said i am new to this so it was kind of trial and error (alot more error) with diffrent attachments and it took forever just to do a lil piece and it still was not acceptable maybe if i knew what to use to do it right i might be able to do it?!?
Reply
Thanks given by:


Messages In This Thread
help with angle iron's - by dbreeze225 - 01-10-2015, 06:55 PM
RE: help with angle iron's - by PixMan - 01-10-2015, 07:33 PM
RE: help with angle iron's - by dbreeze225 - 01-10-2015, 08:06 PM
RE: help with angle iron's - by EdK - 01-10-2015, 08:22 PM
RE: help with angle iron's - by Highpower - 01-10-2015, 09:39 PM
RE: help with angle iron's - by f350ca - 01-10-2015, 10:00 PM
RE: help with angle iron's - by PixMan - 01-10-2015, 10:52 PM
RE: help with angle iron's - by trevatxtal - 01-11-2015, 08:29 AM
RE: help with angle iron's - by dbreeze225 - 01-11-2015, 11:33 AM
RE: help with angle iron's - by EdK - 01-11-2015, 11:59 AM
RE: help with angle iron's - by dbreeze225 - 01-11-2015, 12:10 PM
RE: help with angle iron's - by EdK - 01-11-2015, 12:19 PM
RE: help with angle iron's - by Dr Stan - 01-12-2015, 11:48 AM
RE: help with angle iron's - by dbreeze225 - 01-12-2015, 12:31 PM
RE: help with angle iron's - by stevec - 01-13-2015, 08:05 AM
RE: help with angle iron's - by Mayhem - 01-13-2015, 08:49 AM
RE: help with angle iron's - by EdK - 01-13-2015, 09:54 AM
RE: help with angle iron's - by dbreeze225 - 01-13-2015, 12:19 PM
RE: help with angle iron's - by EdK - 01-13-2015, 12:42 PM
RE: help with angle iron's - by dbreeze225 - 01-13-2015, 01:00 PM
RE: help with angle iron's - by DaveH - 01-13-2015, 01:58 PM
RE: help with angle iron's - by DaveH - 01-13-2015, 02:16 PM
RE: help with angle iron's - by dbreeze225 - 01-13-2015, 04:53 PM
RE: help with angle iron's - by EdK - 01-13-2015, 05:41 PM
RE: help with angle iron's - by DaveH - 01-13-2015, 06:10 PM
RE: help with angle iron's - by dbreeze225 - 01-13-2015, 08:17 PM
RE: help with angle iron's - by DaveH - 01-13-2015, 08:58 PM
RE: help with angle iron's - by dbreeze225 - 01-14-2015, 01:18 PM
RE: help with angle iron's - by DaveH - 01-14-2015, 01:39 PM
RE: help with angle iron's - by dbreeze225 - 01-14-2015, 02:20 PM
RE: help with angle iron's - by EdK - 01-14-2015, 05:00 PM
RE: help with angle iron's - by f350ca - 01-14-2015, 05:54 PM
RE: help with angle iron's - by Dr Stan - 01-14-2015, 07:19 PM
RE: help with angle iron's - by dbreeze225 - 01-15-2015, 12:27 PM
RE: help with angle iron's - by DaveH - 01-15-2015, 01:06 PM
RE: help with angle iron's - by DaveH - 01-15-2015, 01:11 PM
RE: help with angle iron's - by Highpower - 01-15-2015, 02:50 PM
RE: help with angle iron's - by DaveH - 01-15-2015, 03:07 PM
RE: help with angle iron's - by EdK - 01-15-2015, 06:12 PM
RE: help with angle iron's - by stevec - 01-15-2015, 06:33 PM
RE: help with angle iron's - by EdK - 01-15-2015, 06:36 PM
RE: help with angle iron's - by DaveH - 01-15-2015, 06:58 PM
RE: help with angle iron's - by dbreeze225 - 01-16-2015, 06:40 PM
RE: help with angle iron's - by EdK - 01-16-2015, 06:55 PM
RE: help with angle iron's - by DaveH - 01-16-2015, 06:56 PM
RE: help with angle iron's - by dbreeze225 - 01-16-2015, 07:12 PM
RE: help with angle iron's - by dbreeze225 - 01-16-2015, 07:20 PM
RE: help with angle iron's - by DaveH - 01-16-2015, 07:23 PM
RE: help with angle iron's - by EdK - 01-16-2015, 07:29 PM
RE: help with angle iron's - by f350ca - 01-16-2015, 08:59 PM
RE: help with angle iron's - by EdK - 01-16-2015, 09:12 PM
RE: help with angle iron's - by dbreeze225 - 01-17-2015, 01:11 PM
RE: help with angle iron's - by DaveH - 01-17-2015, 01:35 PM
RE: help with angle iron's - by dbreeze225 - 01-17-2015, 01:41 PM
RE: help with angle iron's - by EdK - 01-17-2015, 02:05 PM
RE: help with angle iron's - by dbreeze225 - 01-17-2015, 04:25 PM
RE: help with angle iron's - by DaveH - 01-23-2015, 07:12 PM
RE: help with angle iron's - by rleete - 01-23-2015, 08:20 PM



Users browsing this thread: 12 Guest(s)