MetalworkingFun Forum › Machinery › Other Machinery › Shapers v
Setting stroke on Douglas Shaper

Thread Modes
Setting stroke on Douglas Shaper
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
The following 4 users Like dallen's post:
kenne (09-24-2014), DaveH (09-25-2014), Mayhem (09-25-2014), Shawn (09-25-2014)
#24
09-24-2014, 09:18 PM (This post was last modified: 09-24-2014, 09:19 PM by dallen.)
just something to keep me busy what with being forced into retirement.

Heres a little video of the pour, I didn't video all the time it took to melt just the pour a shake out.





DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by: Shawn


Messages In This Thread
Setting stroke on Douglas Shaper - by Shawn - 09-19-2014, 03:23 PM
RE: Setting stroke on Douglas Shaper - by dallen - 09-19-2014, 03:28 PM
RE: Setting stroke on Douglas Shaper - by Shawn - 09-19-2014, 04:35 PM
RE: Setting stroke on Douglas Shaper - by f350ca - 09-19-2014, 04:42 PM
RE: Setting stroke on Douglas Shaper - by dallen - 09-19-2014, 06:57 PM
RE: Setting stroke on Douglas Shaper - by Mayhem - 09-19-2014, 11:30 PM
RE: Setting stroke on Douglas Shaper - by Shawn - 09-20-2014, 01:00 AM
RE: Setting stroke on Douglas Shaper - by Shawn - 09-20-2014, 01:05 AM
RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 01:18 AM
RE: Setting stroke on Douglas Shaper - by dallen - 09-23-2014, 08:59 AM
RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 02:05 PM
RE: Setting stroke on Douglas Shaper - by dallen - 09-23-2014, 02:50 PM
RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 04:14 PM
RE: Setting stroke on Douglas Shaper - by f350ca - 09-23-2014, 04:55 PM
RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 06:04 PM
RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 06:08 PM
RE: Setting stroke on Douglas Shaper - by dallen - 09-23-2014, 06:24 PM
RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 08:00 PM
RE: Setting stroke on Douglas Shaper - by Shawn - 09-23-2014, 08:05 PM
RE: Setting stroke on Douglas Shaper - by f350ca - 09-23-2014, 09:08 PM
RE: Setting stroke on Douglas Shaper - by dallen - 09-23-2014, 09:23 PM
RE: Setting stroke on Douglas Shaper - by dallen - 09-24-2014, 05:35 PM
RE: Setting stroke on Douglas Shaper - by Shawn - 09-24-2014, 07:30 PM
RE: Setting stroke on Douglas Shaper - by dallen - 09-24-2014, 09:18 PM
RE: Setting stroke on Douglas Shaper - by Shawn - 09-25-2014, 01:20 AM
RE: Setting stroke on Douglas Shaper - by dallen - 09-25-2014, 07:34 AM
RE: Setting stroke on Douglas Shaper - by Shawn - 09-25-2014, 11:50 AM



Users browsing this thread: 3 Guest(s)