what's the best way to ream out 1 1/16 holes to 1 1/4

Hello There, Guest! Register

Thread Modes

what's the best way to ream out 1 1/16 holes to 1 1/4

dallen Offline

Offline

Senior

Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma

#9

06-29-2014, 01:40 PM

I would use an 1.25 counter bore with a 1.062 pilot on it in a mag drill, to run a bridge reamer thru that thick material will take some power.

DA

dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue

Tongue

Reply

« Next Oldest | Next Newest »

Messages In This Thread

what's the best way to ream out 1 1/16 holes to 1 1/4 - by tackit - 06-28-2014, 05:12 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by PixMan - 06-28-2014, 06:35 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by tackit - 06-28-2014, 08:11 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by Mayhem - 06-28-2014, 08:31 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by tackit - 06-28-2014, 08:51 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by tackit - 06-28-2014, 08:54 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by Dr Stan - 06-29-2014, 11:41 AM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by tackit - 06-29-2014, 01:27 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by Dr Stan - 06-29-2014, 02:43 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by tackit - 06-29-2014, 10:34 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by dallen - 06-29-2014, 01:40 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by Dr Stan - 07-01-2014, 05:05 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by stevec - 07-02-2014, 05:55 AM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by Mayhem - 07-02-2014, 07:25 AM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by Dr Stan - 07-04-2014, 10:31 AM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by tackit - 07-04-2014, 02:50 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by Dr Stan - 07-08-2014, 07:07 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by Mayhem - 07-04-2014, 06:27 PM

RE: what's the best way to ream out 1 1/16 holes to 1 1/4 - by Dr Stan - 07-08-2014, 06:54 PM

Users browsing this thread: 2 Guest(s)