MetalworkingFun Forum › Machinery › Milling Machines v
Kondia FV-1 Table/Saddle/Knee/Turret and Ram removal

Thread Modes
Kondia FV-1 Table/Saddle/Knee/Turret and Ram removal
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#50
05-21-2014, 07:33 AM
Thanks again Willie but I've just measured the flange on the end of the pin and it is 42mm, so I'll make a matching nut once I get the mill running. It will make a good project for me.
Hunting American dentists since 2015.
Reply
Thanks given by:


Messages In This Thread
RE: Removing a table from a mill - by TomG - 06-19-2012, 08:03 AM
RE: Removing a table from a mill - by Bill Gruby - 06-19-2012, 08:22 AM
RE: Removing a table from a mill - by Mayhem - 06-19-2012, 08:51 AM
RE: Removing a table from a mill - by TomG - 06-19-2012, 09:33 AM
RE: Removing a table from a mill - by ScrapMetal - 06-19-2012, 01:57 PM
RE: Removing a table from a mill - by EdK - 06-19-2012, 04:49 PM
RE: Removing a table from a mill - by f350ca - 06-19-2012, 07:19 PM
RE: Removing a table from a mill - by Mayhem - 06-20-2012, 12:42 AM
RE: Removing a table from a mill - by stevec - 06-20-2012, 01:38 PM
RE: Removing a table from a mill - by ScrapMetal - 06-20-2012, 03:09 PM
RE: Removing a table from a mill - by doubleboost - 06-20-2012, 03:18 PM
RE: Removing a table from a mill - by ScrapMetal - 06-20-2012, 07:17 PM
RE: Removing a table from a mill - by stevec - 06-21-2012, 07:26 AM
RE: Removing a table from a mill - by ScrapMetal - 06-21-2012, 07:50 PM
RE: Removing a table from a mill - by arvidj - 06-21-2012, 07:18 PM
RE: Removing a table from a mill - by November X-ray - 06-22-2012, 05:26 AM
RE: Removing a table from a mill - by Mayhem - 06-22-2012, 06:12 AM
RE: Removing a table from a mill - by ScrapMetal - 06-22-2012, 02:54 PM
RE: Removing a table from a mill - by Mayhem - 06-22-2012, 09:48 PM
RE: Kondia FV-1 Table removal - by Mayhem - 10-21-2012, 06:09 AM
RE: Kondia FV-1 Table removal - by Mayhem - 10-31-2012, 07:04 PM
RE: Kondia FV-1 Table removal - by Mayhem - 11-01-2012, 09:51 AM
RE: Kondia FV-1 Table removal - by Highpower - 11-04-2012, 06:48 AM
RE: Kondia FV-1 Table removal - by TomG - 11-02-2012, 06:31 AM
RE: Kondia FV-1 Table/Saddle/Knee/Turret and Ram removal - by Mayhem - 05-21-2014, 07:33 AM



Users browsing this thread: 3 Guest(s)