Hardinge Lathe
#58
Greg,

I'll send you a drawing of the wrench.

There is no adjustment on the tailstock, it's ground to fit. You probably just need to clean and lube the front of the way and matching dovetail.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:


Messages In This Thread
Hardinge Lathe - by f350ca - 11-23-2012, 10:42 AM
RE: Hardinge Lathe - by dalee - 11-23-2012, 04:55 PM
RE: Hardinge Lathe - by stevec - 11-23-2012, 05:59 PM
RE: Hardinge Lathe - by f350ca - 11-23-2012, 07:40 PM
RE: Hardinge Lathe - by dalee - 11-24-2012, 10:41 AM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 11:09 AM
RE: Hardinge Lathe - by stevec - 11-24-2012, 11:16 AM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 11:23 AM
RE: Hardinge Lathe - by EdK - 11-24-2012, 12:01 PM
RE: Hardinge Lathe - by stevec - 11-24-2012, 01:30 PM
RE: Hardinge Lathe - by PixMan - 11-24-2012, 05:15 PM
RE: Hardinge Lathe - by TomG - 11-24-2012, 07:58 PM
RE: Hardinge Lathe - by stevec - 11-24-2012, 09:08 PM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 08:09 PM
RE: Hardinge Lathe - by TomG - 11-24-2012, 11:03 PM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 11:07 PM
RE: Hardinge Lathe - by stevec - 11-25-2012, 08:16 AM
RE: Hardinge Lathe - by sasquatch - 11-25-2012, 09:10 AM
RE: Hardinge Lathe - by TomG - 11-28-2012, 12:39 AM
RE: Hardinge Lathe - by f350ca - 11-28-2012, 01:21 AM
RE: Hardinge Lathe - by TomG - 11-28-2012, 07:20 AM
RE: Hardinge Lathe - by f350ca - 11-29-2012, 06:17 PM
RE: Hardinge Lathe - by f350ca - 03-03-2014, 07:23 PM
RE: Hardinge Lathe - by TomG - 03-03-2014, 07:57 PM
RE: Hardinge Lathe - by f350ca - 03-03-2014, 08:11 PM
RE: Hardinge Lathe - by PixMan - 03-04-2014, 07:07 AM
RE: Hardinge Lathe - by Mayhem - 03-04-2014, 07:13 AM
RE: Hardinge Lathe - by f350ca - 03-04-2014, 07:55 PM
RE: Hardinge Lathe - by EdK - 03-05-2014, 07:35 AM
RE: Hardinge Lathe - by Mayhem - 03-05-2014, 09:16 AM
RE: Hardinge Lathe - by f350ca - 03-05-2014, 09:50 AM
RE: Hardinge Lathe - by f350ca - 03-09-2014, 01:41 PM
RE: Hardinge Lathe - by f350ca - 03-09-2014, 05:48 PM
RE: Hardinge Lathe - by f350ca - 03-11-2014, 08:19 PM
RE: Hardinge Lathe - by Mayhem - 03-11-2014, 08:28 PM
RE: Hardinge Lathe - by TomG - 03-12-2014, 04:43 PM
RE: Hardinge Lathe - by f350ca - 03-12-2014, 08:44 PM
RE: Hardinge Lathe - by TomG - 03-12-2014, 09:32 PM
RE: Hardinge Lathe - by f350ca - 03-12-2014, 10:36 PM
RE: Hardinge Lathe - by EdK - 03-13-2014, 05:13 AM
RE: Hardinge Lathe - by f350ca - 03-13-2014, 12:45 PM
RE: Hardinge Lathe - by EdK - 03-13-2014, 04:04 PM
RE: Hardinge Lathe - by TomG - 03-13-2014, 07:04 AM
RE: Hardinge Lathe - by f350ca - 03-13-2014, 07:37 PM
RE: Hardinge Lathe - by Mayhem - 03-13-2014, 09:15 PM
RE: Hardinge Lathe - by f350ca - 03-13-2014, 10:08 PM
RE: Hardinge Lathe - by Mayhem - 03-13-2014, 10:14 PM
RE: Hardinge Lathe - by EdK - 03-14-2014, 05:24 AM
RE: Hardinge Lathe - by DaveH - 03-14-2014, 11:38 AM
RE: Hardinge Lathe - by f350ca - 03-14-2014, 05:27 PM
RE: Hardinge Lathe - by EdK - 03-14-2014, 06:14 PM
RE: Hardinge Lathe - by f350ca - 03-14-2014, 06:52 PM
RE: Hardinge Lathe - by f350ca - 03-16-2014, 09:52 PM
RE: Hardinge Lathe - by PixMan - 03-16-2014, 10:29 PM
RE: Hardinge Lathe - by Shawn - 03-17-2014, 01:06 AM
RE: Hardinge Lathe - by EdK - 03-17-2014, 06:22 AM
RE: Hardinge Lathe - by f350ca - 03-17-2014, 04:54 PM
RE: Hardinge Lathe - by TomG - 03-17-2014, 06:09 PM
RE: Hardinge Lathe - by f350ca - 03-17-2014, 07:14 PM
RE: Hardinge Lathe - by TomG - 03-18-2014, 06:04 PM
RE: Hardinge Lathe - by f350ca - 03-18-2014, 07:40 PM



Users browsing this thread: 1 Guest(s)