|
Hardinge Lathe
|
03-13-2014, 10:08 PM
Was ground finish on the original, may as well keep it the same, thats where you'll get the most hot cuttings as well, those and paint don't mix. The front of the apron is off in the photo, still need to repair the gear that meshes with the rack before it goes on.
Free advice is worth exactly what you payed for it.
Greg |
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
Hardinge Lathe - by f350ca - 11-23-2012, 10:42 AM
RE: Hardinge Lathe - by dalee - 11-23-2012, 04:55 PM
RE: Hardinge Lathe - by stevec - 11-23-2012, 05:59 PM
RE: Hardinge Lathe - by f350ca - 11-23-2012, 07:40 PM
RE: Hardinge Lathe - by dalee - 11-24-2012, 10:41 AM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 11:09 AM
RE: Hardinge Lathe - by stevec - 11-24-2012, 11:16 AM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 11:23 AM
RE: Hardinge Lathe - by EdK - 11-24-2012, 12:01 PM
RE: Hardinge Lathe - by stevec - 11-24-2012, 01:30 PM
RE: Hardinge Lathe - by PixMan - 11-24-2012, 05:15 PM
RE: Hardinge Lathe - by TomG - 11-24-2012, 07:58 PM
RE: Hardinge Lathe - by stevec - 11-24-2012, 09:08 PM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 08:09 PM
RE: Hardinge Lathe - by TomG - 11-24-2012, 11:03 PM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 11:07 PM
RE: Hardinge Lathe - by stevec - 11-25-2012, 08:16 AM
RE: Hardinge Lathe - by sasquatch - 11-25-2012, 09:10 AM
RE: Hardinge Lathe - by TomG - 11-28-2012, 12:39 AM
RE: Hardinge Lathe - by f350ca - 11-28-2012, 01:21 AM
RE: Hardinge Lathe - by TomG - 11-28-2012, 07:20 AM
RE: Hardinge Lathe - by f350ca - 11-29-2012, 06:17 PM
RE: Hardinge Lathe - by f350ca - 03-03-2014, 07:23 PM
RE: Hardinge Lathe - by TomG - 03-03-2014, 07:57 PM
RE: Hardinge Lathe - by f350ca - 03-03-2014, 08:11 PM
RE: Hardinge Lathe - by PixMan - 03-04-2014, 07:07 AM
RE: Hardinge Lathe - by Mayhem - 03-04-2014, 07:13 AM
RE: Hardinge Lathe - by f350ca - 03-04-2014, 07:55 PM
RE: Hardinge Lathe - by EdK - 03-05-2014, 07:35 AM
RE: Hardinge Lathe - by Mayhem - 03-05-2014, 09:16 AM
RE: Hardinge Lathe - by f350ca - 03-05-2014, 09:50 AM
RE: Hardinge Lathe - by f350ca - 03-09-2014, 01:41 PM
RE: Hardinge Lathe - by f350ca - 03-09-2014, 05:48 PM
RE: Hardinge Lathe - by f350ca - 03-11-2014, 08:19 PM
RE: Hardinge Lathe - by Mayhem - 03-11-2014, 08:28 PM
RE: Hardinge Lathe - by TomG - 03-12-2014, 04:43 PM
RE: Hardinge Lathe - by f350ca - 03-12-2014, 08:44 PM
RE: Hardinge Lathe - by TomG - 03-12-2014, 09:32 PM
RE: Hardinge Lathe - by f350ca - 03-12-2014, 10:36 PM
RE: Hardinge Lathe - by EdK - 03-13-2014, 05:13 AM
RE: Hardinge Lathe - by f350ca - 03-13-2014, 12:45 PM
RE: Hardinge Lathe - by EdK - 03-13-2014, 04:04 PM
RE: Hardinge Lathe - by TomG - 03-13-2014, 07:04 AM
RE: Hardinge Lathe - by f350ca - 03-13-2014, 07:37 PM
RE: Hardinge Lathe - by Mayhem - 03-13-2014, 09:15 PM
RE: Hardinge Lathe - by f350ca - 03-13-2014, 10:08 PM
RE: Hardinge Lathe - by Mayhem - 03-13-2014, 10:14 PM
RE: Hardinge Lathe - by EdK - 03-14-2014, 05:24 AM
RE: Hardinge Lathe - by DaveH - 03-14-2014, 11:38 AM
RE: Hardinge Lathe - by f350ca - 03-14-2014, 05:27 PM
RE: Hardinge Lathe - by EdK - 03-14-2014, 06:14 PM
RE: Hardinge Lathe - by f350ca - 03-14-2014, 06:52 PM
RE: Hardinge Lathe - by f350ca - 03-16-2014, 09:52 PM
RE: Hardinge Lathe - by PixMan - 03-16-2014, 10:29 PM
RE: Hardinge Lathe - by Shawn - 03-17-2014, 01:06 AM
RE: Hardinge Lathe - by EdK - 03-17-2014, 06:22 AM
RE: Hardinge Lathe - by f350ca - 03-17-2014, 04:54 PM
RE: Hardinge Lathe - by TomG - 03-17-2014, 06:09 PM
RE: Hardinge Lathe - by f350ca - 03-17-2014, 07:14 PM
RE: Hardinge Lathe - by TomG - 03-18-2014, 06:04 PM
RE: Hardinge Lathe - by f350ca - 03-18-2014, 07:40 PM
|
