MetalworkingFun Forum › Machining › General Metalworking Discussion v
Hardinge Lathe

Thread Modes
Hardinge Lathe
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#40
03-13-2014, 05:13 AM
(03-12-2014, 10:36 PM)f350ca Wrote: The little oil pump on the carriage has sae 20 oil marked on it. Think yours might have the teflon wear pad on the bottom of the saddle, mine is scraped metal, would that make a difference? With a little heavier oil it wouldn't move.

Greg,

Vactra #2 is SAE 20.

Ed
Reply
Thanks given by:


Messages In This Thread
Hardinge Lathe - by f350ca - 11-23-2012, 10:42 AM
RE: Hardinge Lathe - by dalee - 11-23-2012, 04:55 PM
RE: Hardinge Lathe - by stevec - 11-23-2012, 05:59 PM
RE: Hardinge Lathe - by f350ca - 11-23-2012, 07:40 PM
RE: Hardinge Lathe - by dalee - 11-24-2012, 10:41 AM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 11:09 AM
RE: Hardinge Lathe - by stevec - 11-24-2012, 11:16 AM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 11:23 AM
RE: Hardinge Lathe - by EdK - 11-24-2012, 12:01 PM
RE: Hardinge Lathe - by stevec - 11-24-2012, 01:30 PM
RE: Hardinge Lathe - by PixMan - 11-24-2012, 05:15 PM
RE: Hardinge Lathe - by TomG - 11-24-2012, 07:58 PM
RE: Hardinge Lathe - by stevec - 11-24-2012, 09:08 PM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 08:09 PM
RE: Hardinge Lathe - by TomG - 11-24-2012, 11:03 PM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 11:07 PM
RE: Hardinge Lathe - by stevec - 11-25-2012, 08:16 AM
RE: Hardinge Lathe - by sasquatch - 11-25-2012, 09:10 AM
RE: Hardinge Lathe - by TomG - 11-28-2012, 12:39 AM
RE: Hardinge Lathe - by f350ca - 11-28-2012, 01:21 AM
RE: Hardinge Lathe - by TomG - 11-28-2012, 07:20 AM
RE: Hardinge Lathe - by f350ca - 11-29-2012, 06:17 PM
RE: Hardinge Lathe - by f350ca - 03-03-2014, 07:23 PM
RE: Hardinge Lathe - by TomG - 03-03-2014, 07:57 PM
RE: Hardinge Lathe - by f350ca - 03-03-2014, 08:11 PM
RE: Hardinge Lathe - by PixMan - 03-04-2014, 07:07 AM
RE: Hardinge Lathe - by Mayhem - 03-04-2014, 07:13 AM
RE: Hardinge Lathe - by f350ca - 03-04-2014, 07:55 PM
RE: Hardinge Lathe - by EdK - 03-05-2014, 07:35 AM
RE: Hardinge Lathe - by Mayhem - 03-05-2014, 09:16 AM
RE: Hardinge Lathe - by f350ca - 03-05-2014, 09:50 AM
RE: Hardinge Lathe - by f350ca - 03-09-2014, 01:41 PM
RE: Hardinge Lathe - by f350ca - 03-09-2014, 05:48 PM
RE: Hardinge Lathe - by f350ca - 03-11-2014, 08:19 PM
RE: Hardinge Lathe - by Mayhem - 03-11-2014, 08:28 PM
RE: Hardinge Lathe - by TomG - 03-12-2014, 04:43 PM
RE: Hardinge Lathe - by f350ca - 03-12-2014, 08:44 PM
RE: Hardinge Lathe - by TomG - 03-12-2014, 09:32 PM
RE: Hardinge Lathe - by f350ca - 03-12-2014, 10:36 PM
RE: Hardinge Lathe - by EdK - 03-13-2014, 05:13 AM
RE: Hardinge Lathe - by f350ca - 03-13-2014, 12:45 PM
RE: Hardinge Lathe - by EdK - 03-13-2014, 04:04 PM
RE: Hardinge Lathe - by TomG - 03-13-2014, 07:04 AM
RE: Hardinge Lathe - by f350ca - 03-13-2014, 07:37 PM
RE: Hardinge Lathe - by Mayhem - 03-13-2014, 09:15 PM
RE: Hardinge Lathe - by f350ca - 03-13-2014, 10:08 PM
RE: Hardinge Lathe - by Mayhem - 03-13-2014, 10:14 PM
RE: Hardinge Lathe - by EdK - 03-14-2014, 05:24 AM
RE: Hardinge Lathe - by DaveH - 03-14-2014, 11:38 AM
RE: Hardinge Lathe - by f350ca - 03-14-2014, 05:27 PM
RE: Hardinge Lathe - by EdK - 03-14-2014, 06:14 PM
RE: Hardinge Lathe - by f350ca - 03-14-2014, 06:52 PM
RE: Hardinge Lathe - by f350ca - 03-16-2014, 09:52 PM
RE: Hardinge Lathe - by PixMan - 03-16-2014, 10:29 PM
RE: Hardinge Lathe - by Shawn - 03-17-2014, 01:06 AM
RE: Hardinge Lathe - by EdK - 03-17-2014, 06:22 AM
RE: Hardinge Lathe - by f350ca - 03-17-2014, 04:54 PM
RE: Hardinge Lathe - by TomG - 03-17-2014, 06:09 PM
RE: Hardinge Lathe - by f350ca - 03-17-2014, 07:14 PM
RE: Hardinge Lathe - by TomG - 03-18-2014, 06:04 PM
RE: Hardinge Lathe - by f350ca - 03-18-2014, 07:40 PM



Users browsing this thread: 5 Guest(s)