MetalworkingFun Forum › Machining › General Metalworking Discussion v
Hardinge Lathe

Thread Modes
Hardinge Lathe
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#25
03-03-2014, 08:11 PM
This was the predecessor to your lathe Tom. Same basic design with a lot of the same parts but a narrower bed plate. More pictures to follow.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:


Messages In This Thread
Hardinge Lathe - by f350ca - 11-23-2012, 10:42 AM
RE: Hardinge Lathe - by dalee - 11-23-2012, 04:55 PM
RE: Hardinge Lathe - by stevec - 11-23-2012, 05:59 PM
RE: Hardinge Lathe - by f350ca - 11-23-2012, 07:40 PM
RE: Hardinge Lathe - by dalee - 11-24-2012, 10:41 AM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 11:09 AM
RE: Hardinge Lathe - by stevec - 11-24-2012, 11:16 AM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 11:23 AM
RE: Hardinge Lathe - by EdK - 11-24-2012, 12:01 PM
RE: Hardinge Lathe - by stevec - 11-24-2012, 01:30 PM
RE: Hardinge Lathe - by PixMan - 11-24-2012, 05:15 PM
RE: Hardinge Lathe - by TomG - 11-24-2012, 07:58 PM
RE: Hardinge Lathe - by stevec - 11-24-2012, 09:08 PM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 08:09 PM
RE: Hardinge Lathe - by TomG - 11-24-2012, 11:03 PM
RE: Hardinge Lathe - by f350ca - 11-24-2012, 11:07 PM
RE: Hardinge Lathe - by stevec - 11-25-2012, 08:16 AM
RE: Hardinge Lathe - by sasquatch - 11-25-2012, 09:10 AM
RE: Hardinge Lathe - by TomG - 11-28-2012, 12:39 AM
RE: Hardinge Lathe - by f350ca - 11-28-2012, 01:21 AM
RE: Hardinge Lathe - by TomG - 11-28-2012, 07:20 AM
RE: Hardinge Lathe - by f350ca - 11-29-2012, 06:17 PM
RE: Hardinge Lathe - by f350ca - 03-03-2014, 07:23 PM
RE: Hardinge Lathe - by TomG - 03-03-2014, 07:57 PM
RE: Hardinge Lathe - by f350ca - 03-03-2014, 08:11 PM
RE: Hardinge Lathe - by PixMan - 03-04-2014, 07:07 AM
RE: Hardinge Lathe - by Mayhem - 03-04-2014, 07:13 AM
RE: Hardinge Lathe - by f350ca - 03-04-2014, 07:55 PM
RE: Hardinge Lathe - by EdK - 03-05-2014, 07:35 AM
RE: Hardinge Lathe - by Mayhem - 03-05-2014, 09:16 AM
RE: Hardinge Lathe - by f350ca - 03-05-2014, 09:50 AM
RE: Hardinge Lathe - by f350ca - 03-09-2014, 01:41 PM
RE: Hardinge Lathe - by f350ca - 03-09-2014, 05:48 PM
RE: Hardinge Lathe - by f350ca - 03-11-2014, 08:19 PM
RE: Hardinge Lathe - by Mayhem - 03-11-2014, 08:28 PM
RE: Hardinge Lathe - by TomG - 03-12-2014, 04:43 PM
RE: Hardinge Lathe - by f350ca - 03-12-2014, 08:44 PM
RE: Hardinge Lathe - by TomG - 03-12-2014, 09:32 PM
RE: Hardinge Lathe - by f350ca - 03-12-2014, 10:36 PM
RE: Hardinge Lathe - by EdK - 03-13-2014, 05:13 AM
RE: Hardinge Lathe - by f350ca - 03-13-2014, 12:45 PM
RE: Hardinge Lathe - by EdK - 03-13-2014, 04:04 PM
RE: Hardinge Lathe - by TomG - 03-13-2014, 07:04 AM
RE: Hardinge Lathe - by f350ca - 03-13-2014, 07:37 PM
RE: Hardinge Lathe - by Mayhem - 03-13-2014, 09:15 PM
RE: Hardinge Lathe - by f350ca - 03-13-2014, 10:08 PM
RE: Hardinge Lathe - by Mayhem - 03-13-2014, 10:14 PM
RE: Hardinge Lathe - by EdK - 03-14-2014, 05:24 AM
RE: Hardinge Lathe - by DaveH - 03-14-2014, 11:38 AM
RE: Hardinge Lathe - by f350ca - 03-14-2014, 05:27 PM
RE: Hardinge Lathe - by EdK - 03-14-2014, 06:14 PM
RE: Hardinge Lathe - by f350ca - 03-14-2014, 06:52 PM
RE: Hardinge Lathe - by f350ca - 03-16-2014, 09:52 PM
RE: Hardinge Lathe - by PixMan - 03-16-2014, 10:29 PM
RE: Hardinge Lathe - by Shawn - 03-17-2014, 01:06 AM
RE: Hardinge Lathe - by EdK - 03-17-2014, 06:22 AM
RE: Hardinge Lathe - by f350ca - 03-17-2014, 04:54 PM
RE: Hardinge Lathe - by TomG - 03-17-2014, 06:09 PM
RE: Hardinge Lathe - by f350ca - 03-17-2014, 07:14 PM
RE: Hardinge Lathe - by TomG - 03-18-2014, 06:04 PM
RE: Hardinge Lathe - by f350ca - 03-18-2014, 07:40 PM



Users browsing this thread: 5 Guest(s)