|
Thin grooving tools?
|
|
02-08-2014, 09:24 PM
(02-08-2014, 08:00 PM)f350ca Wrote: I was given a grooving tool and some inserts, think I've only used it once, the only time the insert matched the groove I needed. Can't you move the cutter laterally and make the groove as wide as you want it? Unless the insert is wider than the groove you want of course.
Willie
|
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
Thin grooving tools? - by Highpower - 02-08-2014, 12:16 PM
RE: Thin grooving tools? - by EdK - 02-08-2014, 12:18 PM
RE: Thin grooving tools? - by Highpower - 02-08-2014, 12:42 PM
RE: Thin grooving tools? - by EdK - 02-08-2014, 12:48 PM
RE: Thin grooving tools? - by TomG - 02-08-2014, 12:23 PM
RE: Thin grooving tools? - by mfletch - 02-08-2014, 01:20 PM
RE: Thin grooving tools? - by aametalmaster - 02-08-2014, 03:01 PM
RE: Thin grooving tools? - by wrustle - 02-08-2014, 04:16 PM
RE: Thin grooving tools? - by Arbalest - 02-08-2014, 05:18 PM
RE: Thin grooving tools? - by f350ca - 02-08-2014, 08:00 PM
RE: Thin grooving tools? - by Highpower - 02-08-2014, 09:24 PM
RE: Thin grooving tools? - by f350ca - 02-08-2014, 09:44 PM
RE: Thin grooving tools? - by Highpower - 02-09-2014, 12:30 AM
RE: Thin grooving tools? - by Highpower - 02-13-2014, 08:23 AM
RE: Thin grooving tools? - by DaveH - 02-13-2014, 01:23 PM
RE: Thin grooving tools? - by stevec - 02-14-2014, 08:13 AM
RE: Thin grooving tools? - by Highpower - 02-14-2014, 09:03 AM
RE: Thin grooving tools? - by Highpower - 02-14-2014, 12:28 AM
RE: Thin grooving tools? - by EdK - 02-14-2014, 07:04 AM
RE: Thin grooving tools? - by Highpower - 02-14-2014, 08:59 AM
RE: Thin grooving tools? - by EdK - 02-14-2014, 04:38 PM
RE: Thin grooving tools? - by Mayhem - 02-14-2014, 07:08 AM
RE: Thin grooving tools? - by TomG - 02-14-2014, 07:06 PM
RE: Thin grooving tools? - by DaveH - 02-16-2014, 05:54 AM
RE: Thin grooving tools? - by EdK - 02-14-2014, 07:16 PM
RE: Thin grooving tools? - by Mayhem - 02-14-2014, 07:17 PM
RE: Thin grooving tools? - by Highpower - 02-15-2014, 02:13 AM
RE: Thin grooving tools? - by PixMan - 02-15-2014, 08:58 AM
RE: Thin grooving tools? - by Mayhem - 02-15-2014, 09:04 AM
RE: Thin grooving tools? - by DaveH - 02-16-2014, 06:00 AM
RE: Thin grooving tools? - by wrustle - 02-16-2014, 01:12 PM
RE: Thin grooving tools? - by EdK - 02-16-2014, 01:21 PM
RE: Thin grooving tools? - by doubleboost - 02-16-2014, 03:44 PM
|
