MetalworkingFun Forum › Machining › General Metalworking Discussion v
Help with drawing a part

Thread Modes
Help with drawing a part
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#14
01-03-2014, 09:41 AM
Thanks for the help guys. I'm going to try get it measured up over the weekend. Until then I'm not going to look into the BP part, as I know other parts on this mill look similar but are quite different.
Hunting American dentists since 2015.
Reply
Thanks given by:


Messages In This Thread
Help with drawing a part - by Mayhem - 01-02-2014, 06:43 AM
RE: Help with drawing a part - by awemawson - 01-02-2014, 09:23 AM
RE: Help with drawing a part - by Mayhem - 01-02-2014, 09:35 AM
RE: Help with drawing a part - by dallen - 01-02-2014, 09:38 AM
RE: Help with drawing a part - by Mayhem - 01-02-2014, 10:02 AM
RE: Help with drawing a part - by Terry S - 01-02-2014, 10:18 AM
RE: Help with drawing a part - by f350ca - 01-02-2014, 11:03 AM
RE: Help with drawing a part - by Mayhem - 01-02-2014, 11:07 AM
RE: Help with drawing a part - by Mayhem - 01-02-2014, 11:09 AM
RE: Help with drawing a part - by TomG - 01-02-2014, 12:11 PM
RE: Help with drawing a part - by EdK - 01-02-2014, 01:17 PM
RE: Help with drawing a part - by f350ca - 01-02-2014, 01:32 PM
RE: Help with drawing a part - by DaveH - 01-02-2014, 02:07 PM
RE: Help with drawing a part - by Mayhem - 01-03-2014, 09:41 AM
RE: Help with drawing a part - by PixMan - 01-03-2014, 07:22 PM
RE: Help with drawing a part - by Mayhem - 01-05-2014, 04:38 AM
RE: Help with drawing a part - by DaveH - 01-05-2014, 09:27 AM
RE: Help with drawing a part - by EdK - 01-05-2014, 10:02 AM
RE: Help with drawing a part - by Mayhem - 01-05-2014, 10:54 AM
RE: Help with drawing a part - by f350ca - 01-05-2014, 11:10 AM
RE: Help with drawing a part - by TomG - 01-05-2014, 11:18 AM
RE: Help with drawing a part - by PixMan - 01-05-2014, 12:22 PM
RE: Help with drawing a part - by Mayhem - 01-05-2014, 11:07 PM
RE: Help with drawing a part - by Mayhem - 01-30-2014, 06:07 AM
RE: Help with drawing a part - by EdK - 01-30-2014, 06:51 AM
RE: Help with drawing a part - by TomG - 01-30-2014, 07:37 AM
RE: Help with drawing a part - by PixMan - 01-30-2014, 07:53 AM
RE: Help with drawing a part - by EdK - 01-30-2014, 08:13 AM
RE: Help with drawing a part - by Mayhem - 01-30-2014, 05:45 PM
RE: Help with drawing a part - by TomG - 01-30-2014, 08:02 PM
RE: Help with drawing a part - by Mayhem - 01-31-2014, 08:33 AM
RE: Help with drawing a part - by TomG - 01-31-2014, 10:07 AM
RE: Help with drawing a part - by EdK - 01-31-2014, 12:43 PM
RE: Help with drawing a part - by DaveH - 01-31-2014, 12:56 PM
RE: Help with drawing a part - by PixMan - 01-31-2014, 03:05 PM
RE: Help with drawing a part - by Mayhem - 01-31-2014, 05:45 PM
RE: Help with drawing a part - by PixMan - 01-31-2014, 09:14 PM
RE: Help with drawing a part - by EdK - 02-01-2014, 09:27 AM
RE: Help with drawing a part - by TomG - 01-31-2014, 09:34 PM
RE: Help with drawing a part - by PixMan - 01-31-2014, 10:59 PM
RE: Help with drawing a part - by PixMan - 02-01-2014, 06:35 PM
RE: Help with drawing a part - by stevec - 02-02-2014, 07:43 AM
RE: Help with drawing a part - by Mayhem - 02-02-2014, 12:21 AM
RE: Help with drawing a part - by PixMan - 02-02-2014, 08:42 AM
RE: Help with drawing a part - by Mayhem - 02-03-2014, 06:45 AM
RE: Help with drawing a part - by Mayhem - 02-04-2014, 06:57 AM
RE: Help with drawing a part - by TomG - 02-04-2014, 07:46 AM
RE: Help with drawing a part - by Mayhem - 02-10-2014, 05:37 AM
RE: Help with drawing a part - by EdK - 02-10-2014, 06:30 AM
RE: Help with drawing a part - by Mayhem - 02-10-2014, 06:58 AM



Users browsing this thread: 10 Guest(s)