Parting on the Lathe

Hello There, Guest! Register

Thread Modes

Parting on the Lathe

TomG Offline

Offline

Alt. Whipping Boy

Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan

#47

12-18-2013, 10:07 AM

Thanks!

The Hardinge is definitely my baby. I bought her new in the mid 80's and she has served me very well over the years. The lacquer is starting to show its age though, gotta figure out a way to repair the chips. It's too bad they didn't switch to polyurethane, it would have been a lot more durable.

Tom

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Parting on the Lathe - by TomG - 12-07-2013, 09:16 PM

RE: Parting on the Lathe - by PixMan - 12-08-2013, 12:04 AM

RE: Parting on the Lathe - by TomG - 12-08-2013, 12:19 AM

RE: Parting on the Lathe - by Shawn - 12-08-2013, 04:08 AM

RE: Parting on the Lathe - by TomG - 12-08-2013, 10:03 AM

RE: Parting on the Lathe - by PixMan - 12-08-2013, 08:27 AM

RE: Parting on the Lathe - by EdK - 12-08-2013, 10:08 AM

RE: Parting on the Lathe - by TomG - 12-09-2013, 09:05 AM

RE: Parting on the Lathe - by EdK - 12-09-2013, 01:10 PM

RE: Parting on the Lathe - by f350ca - 12-08-2013, 10:09 AM

RE: Parting on the Lathe - by TomG - 12-08-2013, 10:09 AM

RE: Parting on the Lathe - by Micktoon - 12-08-2013, 06:16 PM

RE: Parting on the Lathe - by TomG - 12-08-2013, 06:39 PM

RE: Parting on the Lathe - by Hawkeye - 12-08-2013, 11:09 PM

RE: Parting on the Lathe - by TomG - 12-09-2013, 12:07 AM

RE: Parting on the Lathe - by awemawson - 12-09-2013, 04:13 AM

RE: Parting on the Lathe - by TomG - 12-09-2013, 09:09 AM

RE: Parting on the Lathe - by Micktoon - 12-09-2013, 08:27 AM

RE: Parting on the Lathe - by awemawson - 12-09-2013, 10:14 AM

RE: Parting on the Lathe - by TomG - 12-09-2013, 11:32 AM

RE: Parting on the Lathe - by awemawson - 12-09-2013, 12:41 PM

RE: Parting on the Lathe - by PixMan - 12-09-2013, 01:31 PM

RE: Parting on the Lathe - by awemawson - 12-09-2013, 01:41 PM

RE: Parting on the Lathe - by f350ca - 12-09-2013, 01:33 PM

RE: Parting on the Lathe - by paulmo101 - 12-09-2013, 03:02 PM

RE: Parting on the Lathe - by EdK - 12-09-2013, 04:26 PM

RE: Parting on the Lathe - by TomG - 12-09-2013, 05:41 PM

RE: Parting on the Lathe - by EdK - 12-09-2013, 06:18 PM

RE: Parting on the Lathe - by TomG - 12-09-2013, 08:44 PM

RE: Parting on the Lathe - by EdK - 12-10-2013, 06:31 AM

RE: Parting on the Lathe - by PixMan - 12-09-2013, 06:59 PM

RE: Parting on the Lathe - by PixMan - 12-09-2013, 10:03 PM

RE: Parting on the Lathe - by dallen - 12-10-2013, 10:41 AM

RE: Parting on the Lathe - by TomG - 12-10-2013, 10:57 AM

RE: Parting on the Lathe - by dallen - 12-10-2013, 12:30 PM

RE: Parting on the Lathe - by awemawson - 12-10-2013, 12:49 PM

RE: Parting on the Lathe - by PixMan - 12-11-2013, 08:48 AM

RE: Parting on the Lathe - by Mayhem - 12-11-2013, 09:34 AM

RE: Parting on the Lathe - by dallen - 12-11-2013, 09:57 AM

RE: Parting on the Lathe - by TomG - 12-11-2013, 11:20 AM

RE: Parting on the Lathe - by dallen - 12-11-2013, 05:53 PM

RE: Parting on the Lathe - by stevec - 12-11-2013, 11:38 AM

RE: Parting on the Lathe - by TomG - 12-11-2013, 12:24 PM

RE: Parting on the Lathe - by ScrapMetal - 12-11-2013, 05:31 PM

RE: Parting on the Lathe - by EdK - 12-11-2013, 11:42 AM

RE: Parting on the Lathe - by 7mag - 12-18-2013, 09:28 AM

RE: Parting on the Lathe - by TomG - 12-18-2013, 10:07 AM

RE: Parting on the Lathe - by stevec - 07-22-2014, 05:46 PM

RE: Parting on the Lathe - by EdK - 07-22-2014, 06:22 PM

RE: Parting on the Lathe - by stevec - 07-22-2014, 07:48 PM

Users browsing this thread: 5 Guest(s)