|
Parting on the Lathe
|
12-11-2013, 11:38 AM
Tom, someday I'm gonna make a BXA size parting blade holder like that but not with the slant that requires one to adjust the height each time the blade is extended or retracted.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
|
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
Parting on the Lathe - by TomG - 12-07-2013, 09:16 PM
RE: Parting on the Lathe - by PixMan - 12-08-2013, 12:04 AM
RE: Parting on the Lathe - by TomG - 12-08-2013, 12:19 AM
RE: Parting on the Lathe - by Shawn - 12-08-2013, 04:08 AM
RE: Parting on the Lathe - by TomG - 12-08-2013, 10:03 AM
RE: Parting on the Lathe - by PixMan - 12-08-2013, 08:27 AM
RE: Parting on the Lathe - by EdK - 12-08-2013, 10:08 AM
RE: Parting on the Lathe - by TomG - 12-09-2013, 09:05 AM
RE: Parting on the Lathe - by EdK - 12-09-2013, 01:10 PM
RE: Parting on the Lathe - by f350ca - 12-08-2013, 10:09 AM
RE: Parting on the Lathe - by TomG - 12-08-2013, 10:09 AM
RE: Parting on the Lathe - by Micktoon - 12-08-2013, 06:16 PM
RE: Parting on the Lathe - by TomG - 12-08-2013, 06:39 PM
RE: Parting on the Lathe - by Hawkeye - 12-08-2013, 11:09 PM
RE: Parting on the Lathe - by TomG - 12-09-2013, 12:07 AM
RE: Parting on the Lathe - by awemawson - 12-09-2013, 04:13 AM
RE: Parting on the Lathe - by TomG - 12-09-2013, 09:09 AM
RE: Parting on the Lathe - by Micktoon - 12-09-2013, 08:27 AM
RE: Parting on the Lathe - by awemawson - 12-09-2013, 10:14 AM
RE: Parting on the Lathe - by TomG - 12-09-2013, 11:32 AM
RE: Parting on the Lathe - by awemawson - 12-09-2013, 12:41 PM
RE: Parting on the Lathe - by PixMan - 12-09-2013, 01:31 PM
RE: Parting on the Lathe - by awemawson - 12-09-2013, 01:41 PM
RE: Parting on the Lathe - by f350ca - 12-09-2013, 01:33 PM
RE: Parting on the Lathe - by paulmo101 - 12-09-2013, 03:02 PM
RE: Parting on the Lathe - by EdK - 12-09-2013, 04:26 PM
RE: Parting on the Lathe - by TomG - 12-09-2013, 05:41 PM
RE: Parting on the Lathe - by EdK - 12-09-2013, 06:18 PM
RE: Parting on the Lathe - by TomG - 12-09-2013, 08:44 PM
RE: Parting on the Lathe - by EdK - 12-10-2013, 06:31 AM
RE: Parting on the Lathe - by PixMan - 12-09-2013, 06:59 PM
RE: Parting on the Lathe - by PixMan - 12-09-2013, 10:03 PM
RE: Parting on the Lathe - by dallen - 12-10-2013, 10:41 AM
RE: Parting on the Lathe - by TomG - 12-10-2013, 10:57 AM
RE: Parting on the Lathe - by dallen - 12-10-2013, 12:30 PM
RE: Parting on the Lathe - by awemawson - 12-10-2013, 12:49 PM
RE: Parting on the Lathe - by PixMan - 12-11-2013, 08:48 AM
RE: Parting on the Lathe - by Mayhem - 12-11-2013, 09:34 AM
RE: Parting on the Lathe - by dallen - 12-11-2013, 09:57 AM
RE: Parting on the Lathe - by TomG - 12-11-2013, 11:20 AM
RE: Parting on the Lathe - by dallen - 12-11-2013, 05:53 PM
RE: Parting on the Lathe - by stevec - 12-11-2013, 11:38 AM
RE: Parting on the Lathe - by TomG - 12-11-2013, 12:24 PM
RE: Parting on the Lathe - by ScrapMetal - 12-11-2013, 05:31 PM
RE: Parting on the Lathe - by EdK - 12-11-2013, 11:42 AM
RE: Parting on the Lathe - by 7mag - 12-18-2013, 09:28 AM
RE: Parting on the Lathe - by TomG - 12-18-2013, 10:07 AM
RE: Parting on the Lathe - by stevec - 07-22-2014, 05:46 PM
RE: Parting on the Lathe - by EdK - 07-22-2014, 06:22 PM
RE: Parting on the Lathe - by stevec - 07-22-2014, 07:48 PM
|
