Parting on the Lathe

Hello There, Guest! Register

Thread Modes

Parting on the Lathe

TomG Offline

Offline

Alt. Whipping Boy

Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan

#9

12-08-2013, 10:09 AM

Thanks for the info Ken, and the demo. You would never get away with a cut like that without coolant on HSS. There is just too much tool in contact with the work. You are also right about the feed. The natural tendency is to be timid after you've been burned a few times, but faster is usually better.

Tom

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Parting on the Lathe - by TomG - 12-07-2013, 09:16 PM

RE: Parting on the Lathe - by PixMan - 12-08-2013, 12:04 AM

RE: Parting on the Lathe - by TomG - 12-08-2013, 12:19 AM

RE: Parting on the Lathe - by Shawn - 12-08-2013, 04:08 AM

RE: Parting on the Lathe - by TomG - 12-08-2013, 10:03 AM

RE: Parting on the Lathe - by PixMan - 12-08-2013, 08:27 AM

RE: Parting on the Lathe - by EdK - 12-08-2013, 10:08 AM

RE: Parting on the Lathe - by TomG - 12-09-2013, 09:05 AM

RE: Parting on the Lathe - by EdK - 12-09-2013, 01:10 PM

RE: Parting on the Lathe - by f350ca - 12-08-2013, 10:09 AM

RE: Parting on the Lathe - by TomG - 12-08-2013, 10:09 AM

RE: Parting on the Lathe - by Micktoon - 12-08-2013, 06:16 PM

RE: Parting on the Lathe - by TomG - 12-08-2013, 06:39 PM

RE: Parting on the Lathe - by Hawkeye - 12-08-2013, 11:09 PM

RE: Parting on the Lathe - by TomG - 12-09-2013, 12:07 AM

RE: Parting on the Lathe - by awemawson - 12-09-2013, 04:13 AM

RE: Parting on the Lathe - by TomG - 12-09-2013, 09:09 AM

RE: Parting on the Lathe - by Micktoon - 12-09-2013, 08:27 AM

RE: Parting on the Lathe - by awemawson - 12-09-2013, 10:14 AM

RE: Parting on the Lathe - by TomG - 12-09-2013, 11:32 AM

RE: Parting on the Lathe - by awemawson - 12-09-2013, 12:41 PM

RE: Parting on the Lathe - by PixMan - 12-09-2013, 01:31 PM

RE: Parting on the Lathe - by awemawson - 12-09-2013, 01:41 PM

RE: Parting on the Lathe - by f350ca - 12-09-2013, 01:33 PM

RE: Parting on the Lathe - by paulmo101 - 12-09-2013, 03:02 PM

RE: Parting on the Lathe - by EdK - 12-09-2013, 04:26 PM

RE: Parting on the Lathe - by TomG - 12-09-2013, 05:41 PM

RE: Parting on the Lathe - by EdK - 12-09-2013, 06:18 PM

RE: Parting on the Lathe - by TomG - 12-09-2013, 08:44 PM

RE: Parting on the Lathe - by EdK - 12-10-2013, 06:31 AM

RE: Parting on the Lathe - by PixMan - 12-09-2013, 06:59 PM

RE: Parting on the Lathe - by PixMan - 12-09-2013, 10:03 PM

RE: Parting on the Lathe - by dallen - 12-10-2013, 10:41 AM

RE: Parting on the Lathe - by TomG - 12-10-2013, 10:57 AM

RE: Parting on the Lathe - by dallen - 12-10-2013, 12:30 PM

RE: Parting on the Lathe - by awemawson - 12-10-2013, 12:49 PM

RE: Parting on the Lathe - by PixMan - 12-11-2013, 08:48 AM

RE: Parting on the Lathe - by Mayhem - 12-11-2013, 09:34 AM

RE: Parting on the Lathe - by dallen - 12-11-2013, 09:57 AM

RE: Parting on the Lathe - by TomG - 12-11-2013, 11:20 AM

RE: Parting on the Lathe - by dallen - 12-11-2013, 05:53 PM

RE: Parting on the Lathe - by stevec - 12-11-2013, 11:38 AM

RE: Parting on the Lathe - by TomG - 12-11-2013, 12:24 PM

RE: Parting on the Lathe - by ScrapMetal - 12-11-2013, 05:31 PM

RE: Parting on the Lathe - by EdK - 12-11-2013, 11:42 AM

RE: Parting on the Lathe - by 7mag - 12-18-2013, 09:28 AM

RE: Parting on the Lathe - by TomG - 12-18-2013, 10:07 AM

RE: Parting on the Lathe - by stevec - 07-22-2014, 05:46 PM

RE: Parting on the Lathe - by EdK - 07-22-2014, 06:22 PM

RE: Parting on the Lathe - by stevec - 07-22-2014, 07:48 PM

Users browsing this thread: 9 Guest(s)