MetalworkingFun Forum › Machining › General Metalworking Discussion v
Help with drawing

Thread Modes
Help with drawing
claudef Offline
Sophmore
***
Posts: 55
Threads: 5
Joined: Mar 2012
Location: Cornwall, On
#13
04-20-2012, 07:18 AM (This post was last modified: 04-20-2012, 07:19 AM by claudef.)
The most acurate way to measure these 45 deg. faces is over rollers.
You will still need to refer to the other sketch for demensions.
Attached is a sketch of picatinny rail I made last year but never posted.


Attached Files
.pdf   picatinny rail.pdf (Size: 7.17 KB / Downloads: 13)
claudef, proud to be a member of Metalworking Forum since Mar 2012.
Reply
Thanks given by:


Messages In This Thread
Help with drawing - by Turbinedoctor - 04-19-2012, 04:30 AM
RE: Help with drawing - by stevec - 04-19-2012, 07:24 AM
RE: Help with drawing - by EdK - 04-19-2012, 05:26 PM
RE: Help with drawing - by Hopefuldave - 04-19-2012, 05:53 PM
RE: Help with drawing - by EdK - 04-19-2012, 06:39 PM
RE: Help with drawing - by Tony Wells - 04-19-2012, 07:08 PM
RE: Help with drawing - by PixMan - 04-19-2012, 08:27 PM
RE: Help with drawing - by Tony Wells - 04-19-2012, 08:41 PM
RE: Help with drawing - by DanH - 04-19-2012, 11:22 PM
RE: Help with drawing - by Turbinedoctor - 04-19-2012, 11:39 PM
RE: Help with drawing - by Tony Wells - 04-20-2012, 12:27 AM
RE: Help with drawing - by Turbinedoctor - 04-20-2012, 03:00 AM
RE: Help with drawing - by claudef - 04-20-2012, 07:18 AM
RE: Help with drawing - by Tony Wells - 04-20-2012, 08:47 AM
RE: Help with drawing - by Highpower - 04-20-2012, 10:21 AM
RE: Help with drawing - by stevec - 04-20-2012, 06:46 PM
RE: Help with drawing - by EdK - 04-20-2012, 06:52 PM
RE: Help with drawing - by Highpower - 04-20-2012, 08:05 PM
RE: Help with drawing - by EdK - 04-20-2012, 08:10 PM
RE: Help with drawing - by Turbinedoctor - 04-21-2012, 06:53 PM
RE: Help with drawing - by Tony Wells - 04-21-2012, 07:12 PM
RE: Help with drawing - by Turbinedoctor - 04-21-2012, 09:30 PM
RE: Help with drawing - by Turbinedoctor - 05-03-2012, 07:25 PM
RE: Help with drawing - by EdK - 05-03-2012, 07:42 PM
RE: Help with drawing - by DaveH - 05-03-2012, 07:49 PM
RE: Help with drawing - by Turbinedoctor - 05-03-2012, 08:36 PM
RE: Help with drawing - by EdK - 05-04-2012, 06:15 AM
RE: Help with drawing - by Turbinedoctor - 05-03-2012, 08:38 PM
RE: Help with drawing - by Tony Wells - 05-04-2012, 12:32 PM
RE: Help with drawing - by Turbinedoctor - 05-05-2012, 11:30 AM
RE: Help with drawing - by EdK - 05-05-2012, 01:02 PM



Users browsing this thread: 6 Guest(s)