Cutting Speed and RPM on the Lathe and Mill

Hello There, Guest! Register

Thread Modes

Cutting Speed and RPM on the Lathe and Mill

TomG Offline

Offline

Alt. Whipping Boy

Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan

#19

10-02-2013, 07:16 AM

Darren,

I'm debating the value of a feed rate video for the hobby machinist. I can show how to calculate the feed rate based on chip load and rpm, but most powered feeds on home machines are either variable or non-existent. I can't remember the last time I calculated a feed rate and then actually applied it. It's more "that sounds about right" or "the color of the chips is good".

Tom

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Cutting Speed and RPM on the Lathe and Mill - by TomG - 09-30-2013, 11:30 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by b4dyc - 10-01-2013, 05:46 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-01-2013, 07:11 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 08:01 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-01-2013, 08:19 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by b4dyc - 10-01-2013, 08:41 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by PixMan - 10-01-2013, 08:57 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-01-2013, 08:58 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by dallen - 10-01-2013, 09:23 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 10:26 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by stevec - 10-01-2013, 01:03 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by chucketn - 10-01-2013, 11:33 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 01:15 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-01-2013, 08:31 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 08:40 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by f350ca - 10-01-2013, 10:49 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 11:11 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-02-2013, 06:20 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-02-2013, 07:16 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-02-2013, 09:37 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by arvidj - 10-02-2013, 09:20 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-02-2013, 10:25 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-03-2013, 10:17 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-03-2013, 11:35 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Micktoon - 10-03-2013, 05:07 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by Micktoon - 10-04-2013, 04:09 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-04-2013, 08:23 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-03-2013, 07:42 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by henryarnold - 10-03-2013, 11:16 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-04-2013, 05:35 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Highpower - 10-04-2013, 09:41 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-04-2013, 07:16 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-04-2013, 04:05 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-04-2013, 07:13 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by Hawkeye - 10-04-2013, 09:53 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by LJP - 10-04-2013, 11:29 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-04-2013, 07:10 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-05-2013, 09:02 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-05-2013, 10:15 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Micktoon - 10-05-2013, 06:24 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by krv3000 - 10-06-2013, 01:57 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-06-2013, 05:49 PM

Users browsing this thread: 6 Guest(s)