Cutting Speed and RPM on the Lathe and Mill

Hello There, Guest! Register

Thread Modes

Cutting Speed and RPM on the Lathe and Mill

TomG Offline

Offline

Alt. Whipping Boy

Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan

#17

10-01-2013, 11:11 PM

The reason conventional milling creates such a crappy finish is that the cutting edge drags on the work before enough pressure is produced for it to cut. When climb milling, as soon as the cutting edge hits the work, it's cutting, there's no dragging at all.

Tom

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Cutting Speed and RPM on the Lathe and Mill - by TomG - 09-30-2013, 11:30 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by b4dyc - 10-01-2013, 05:46 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-01-2013, 07:11 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 08:01 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-01-2013, 08:19 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by b4dyc - 10-01-2013, 08:41 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by PixMan - 10-01-2013, 08:57 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-01-2013, 08:58 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by dallen - 10-01-2013, 09:23 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 10:26 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by stevec - 10-01-2013, 01:03 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by chucketn - 10-01-2013, 11:33 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 01:15 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-01-2013, 08:31 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 08:40 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by f350ca - 10-01-2013, 10:49 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 11:11 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-02-2013, 06:20 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-02-2013, 07:16 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-02-2013, 09:37 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by arvidj - 10-02-2013, 09:20 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-02-2013, 10:25 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-03-2013, 10:17 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-03-2013, 11:35 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Micktoon - 10-03-2013, 05:07 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by Micktoon - 10-04-2013, 04:09 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-04-2013, 08:23 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-03-2013, 07:42 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by henryarnold - 10-03-2013, 11:16 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-04-2013, 05:35 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Highpower - 10-04-2013, 09:41 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-04-2013, 07:16 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-04-2013, 04:05 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-04-2013, 07:13 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by Hawkeye - 10-04-2013, 09:53 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by LJP - 10-04-2013, 11:29 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-04-2013, 07:10 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-05-2013, 09:02 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-05-2013, 10:15 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Micktoon - 10-05-2013, 06:24 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by krv3000 - 10-06-2013, 01:57 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-06-2013, 05:49 PM

Users browsing this thread: 3 Guest(s)