MetalworkingFun Forum › Machining › Metrology v
Dial Gauges

Thread Modes
Dial Gauges
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
The following 1 user Likes Mayhem's post:
EdK (09-29-2013)
#19
09-29-2013, 04:21 AM
I just picked up this Federal Testmaster T-2 from Ken for $40. I has .0001" resolution and should come in handy. I did try to swap it with his Starrett 709 but it didn't fit into the box Big Grin

   
   
Hunting American dentists since 2015.
Reply
Thanks given by:


Messages In This Thread
Dial Gauges - by DaveH - 12-08-2012, 07:17 AM
RE: Dial Gauges - by PixMan - 12-08-2012, 08:24 AM
RE: Dial Gauges - by DaveH - 12-08-2012, 08:37 AM
RE: Dial Gauges - by PixMan - 12-08-2012, 08:45 AM
RE: Dial Gauges - by krv3000 - 12-08-2012, 05:15 PM
RE: Dial Gauges - by EdK - 12-08-2012, 06:18 PM
RE: Dial Gauges - by Bill Gruby - 12-08-2012, 08:36 PM
RE: Dial Gauges - by doubleboost - 12-08-2012, 08:43 PM
RE: Dial Gauges - by EdK - 12-08-2012, 08:46 PM
RE: Dial Gauges - by PixMan - 12-08-2012, 09:23 PM
RE: Dial Gauges - by EdK - 12-08-2012, 09:29 PM
RE: Dial Gauges - by PixMan - 12-08-2012, 10:18 PM
RE: Dial Gauges - by Bill Gruby - 12-08-2012, 10:51 PM
RE: Dial Gauges - by Mayhem - 12-10-2012, 06:34 AM
RE: Dial Gauges - by EdK - 12-10-2012, 12:37 PM
RE: Dial Gauges - by PixMan - 12-10-2012, 07:46 AM
RE: Dial Gauges - by stevec - 12-10-2012, 01:45 PM
RE: Dial Gauges - by Mayhem - 12-10-2012, 05:12 PM
RE: Dial Gauges - by Mayhem - 09-29-2013, 04:21 AM
RE: Dial Gauges - by chucketn - 09-29-2013, 07:41 AM
RE: Dial Gauges - by Highpower - 09-29-2013, 12:15 PM
RE: Dial Gauges - by DaveH - 09-29-2013, 11:27 AM
RE: Dial Gauges - by EdK - 09-29-2013, 12:26 PM
RE: Dial Gauges - by PixMan - 09-30-2013, 05:42 AM
RE: Dial Gauges - by Mayhem - 09-30-2013, 06:07 AM
RE: Dial Gauges - by eightball - 12-12-2013, 03:06 PM
RE: Dial Gauges - by TomG - 12-12-2013, 07:51 PM
RE: Dial Gauges - by awemawson - 12-13-2013, 04:48 AM
RE: Dial Gauges - by DaveH - 12-13-2013, 05:04 AM
RE: Dial Gauges - by TomG - 12-13-2013, 07:56 AM



Users browsing this thread: 4 Guest(s)