MetalworkingFun Forum › Machinery › Other Machinery › Shapers v
10.5" Douglas Shaper

Thread Modes
10.5" Douglas Shaper
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
#34
08-17-2013, 11:37 AM
back out the bolt that you tighten up to hold the head in position you will have to back it out probably all the way, there should be a wedge pin under it.

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:


Messages In This Thread
10.5" Douglas Shaper - by Mayhem - 08-04-2013, 07:11 AM
RE: 10.5" Douglas Shaper - by dallen - 08-04-2013, 08:12 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-04-2013, 08:22 AM
RE: 10.5" Douglas Shaper - by EdK - 08-04-2013, 08:56 AM
RE: 10.5" Douglas Shaper - by dallen - 08-04-2013, 10:54 AM
RE: 10.5" Douglas Shaper - by sasquatch - 08-04-2013, 06:37 PM
RE: 10.5" Douglas Shaper - by Dave J - 08-04-2013, 10:26 PM
RE: 10.5" Douglas Shaper - by Mayhem - 08-05-2013, 02:42 AM
RE: 10.5" Douglas Shaper - by TomG - 08-05-2013, 11:08 AM
RE: 10.5" Douglas Shaper - by DaveH - 08-05-2013, 11:55 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-05-2013, 05:09 PM
RE: 10.5" Douglas Shaper - by dallen - 08-05-2013, 08:46 PM
RE: 10.5" Douglas Shaper - by Mayhem - 08-06-2013, 09:32 AM
RE: 10.5" Douglas Shaper - by dallen - 08-06-2013, 10:02 AM
RE: 10.5" Douglas Shaper - by Hawkeye - 08-06-2013, 11:17 PM
RE: 10.5" Douglas Shaper - by Dave J - 08-07-2013, 12:26 AM
RE: 10.5" Douglas Shaper - by Dave J - 08-07-2013, 12:43 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-07-2013, 05:34 AM
RE: 10.5" Douglas Shaper - by Dave J - 08-07-2013, 05:43 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-10-2013, 08:33 AM
RE: 10.5" Douglas Shaper - by stevec - 08-10-2013, 12:38 PM
RE: 10.5" Douglas Shaper - by dallen - 08-10-2013, 12:47 PM
RE: 10.5" Douglas Shaper - by f350ca - 08-10-2013, 01:16 PM
RE: 10.5" Douglas Shaper - by dallen - 08-10-2013, 03:13 PM
RE: 10.5" Douglas Shaper - by Mayhem - 08-10-2013, 07:47 PM
RE: 10.5" Douglas Shaper - by Hawkeye - 08-10-2013, 08:13 PM
RE: 10.5" Douglas Shaper - by f350ca - 08-11-2013, 12:47 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-11-2013, 03:02 AM
RE: 10.5" Douglas Shaper - by f350ca - 08-11-2013, 08:56 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-11-2013, 09:02 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-15-2013, 07:01 AM
RE: 10.5" Douglas Shaper - by Dave J - 08-15-2013, 08:36 PM
RE: 10.5" Douglas Shaper - by castellated nut - 01-24-2019, 04:43 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-17-2013, 10:11 AM
RE: 10.5" Douglas Shaper - by dallen - 08-17-2013, 11:37 AM
RE: 10.5" Douglas Shaper - by Mayhem - 08-17-2013, 08:29 PM
RE: 10.5" Douglas Shaper - by Dave J - 08-17-2013, 09:05 PM
RE: 10.5" Douglas Shaper - by Mayhem - 09-03-2013, 08:27 AM
RE: 10.5" Douglas Shaper - by Mayhem - 09-03-2013, 08:31 AM
RE: 10.5" Douglas Shaper - by stevec - 09-03-2013, 11:30 AM
RE: 10.5" Douglas Shaper - by TomG - 01-24-2019, 10:02 AM
RE: 10.5" Douglas Shaper - by castellated nut - 01-24-2019, 05:28 PM



Users browsing this thread: 7 Guest(s)