10.5" Douglas Shaper

Hello There, Guest! Register

Thread Modes

10.5" Douglas Shaper

Hawkeye Offline

Offline

Junior

Posts: 535
Threads: 39
Joined: Jan 2013
Location: Kelowna, BC, Canada

#15

08-06-2013, 11:17 PM

Referring to the picture of the ratchet, the casting to the table side of the 'gear' should move freely over the shaft. It looks like it may be stuck to the shaft. A bunch of oil and some gentle persuasion may help.

Loosen the arm that carries the motion to the ratchet mechanism before you try to free the casting up. no point in putting a bend in it that will cause trouble later.

Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.

Reply

Thanks given by: Mayhem

« Next Oldest | Next Newest »

Messages In This Thread

10.5" Douglas Shaper - by Mayhem - 08-04-2013, 07:11 AM

RE: 10.5" Douglas Shaper - by dallen - 08-04-2013, 08:12 AM

RE: 10.5" Douglas Shaper - by Mayhem - 08-04-2013, 08:22 AM

RE: 10.5" Douglas Shaper - by EdK - 08-04-2013, 08:56 AM

RE: 10.5" Douglas Shaper - by dallen - 08-04-2013, 10:54 AM

RE: 10.5" Douglas Shaper - by sasquatch - 08-04-2013, 06:37 PM

RE: 10.5" Douglas Shaper - by Dave J - 08-04-2013, 10:26 PM

RE: 10.5" Douglas Shaper - by Mayhem - 08-05-2013, 02:42 AM

RE: 10.5" Douglas Shaper - by TomG - 08-05-2013, 11:08 AM

RE: 10.5" Douglas Shaper - by DaveH - 08-05-2013, 11:55 AM

RE: 10.5" Douglas Shaper - by Mayhem - 08-05-2013, 05:09 PM

RE: 10.5" Douglas Shaper - by dallen - 08-05-2013, 08:46 PM

RE: 10.5" Douglas Shaper - by Mayhem - 08-06-2013, 09:32 AM

RE: 10.5" Douglas Shaper - by dallen - 08-06-2013, 10:02 AM

RE: 10.5" Douglas Shaper - by Hawkeye - 08-06-2013, 11:17 PM

RE: 10.5" Douglas Shaper - by Dave J - 08-07-2013, 12:26 AM

RE: 10.5" Douglas Shaper - by Dave J - 08-07-2013, 12:43 AM

RE: 10.5" Douglas Shaper - by Mayhem - 08-07-2013, 05:34 AM

RE: 10.5" Douglas Shaper - by Dave J - 08-07-2013, 05:43 AM

RE: 10.5" Douglas Shaper - by Mayhem - 08-10-2013, 08:33 AM

RE: 10.5" Douglas Shaper - by stevec - 08-10-2013, 12:38 PM

RE: 10.5" Douglas Shaper - by dallen - 08-10-2013, 12:47 PM

RE: 10.5" Douglas Shaper - by f350ca - 08-10-2013, 01:16 PM

RE: 10.5" Douglas Shaper - by dallen - 08-10-2013, 03:13 PM

RE: 10.5" Douglas Shaper - by Mayhem - 08-10-2013, 07:47 PM

RE: 10.5" Douglas Shaper - by Hawkeye - 08-10-2013, 08:13 PM

RE: 10.5" Douglas Shaper - by f350ca - 08-11-2013, 12:47 AM

RE: 10.5" Douglas Shaper - by Mayhem - 08-11-2013, 03:02 AM

RE: 10.5" Douglas Shaper - by f350ca - 08-11-2013, 08:56 AM

RE: 10.5" Douglas Shaper - by Mayhem - 08-11-2013, 09:02 AM

RE: 10.5" Douglas Shaper - by Mayhem - 08-15-2013, 07:01 AM

RE: 10.5" Douglas Shaper - by Dave J - 08-15-2013, 08:36 PM

RE: 10.5" Douglas Shaper - by castellated nut - 01-24-2019, 04:43 AM

RE: 10.5" Douglas Shaper - by Mayhem - 08-17-2013, 10:11 AM

RE: 10.5" Douglas Shaper - by dallen - 08-17-2013, 11:37 AM

RE: 10.5" Douglas Shaper - by Mayhem - 08-17-2013, 08:29 PM

RE: 10.5" Douglas Shaper - by Dave J - 08-17-2013, 09:05 PM

RE: 10.5" Douglas Shaper - by Mayhem - 09-03-2013, 08:27 AM

RE: 10.5" Douglas Shaper - by Mayhem - 09-03-2013, 08:31 AM

RE: 10.5" Douglas Shaper - by stevec - 09-03-2013, 11:30 AM

RE: 10.5" Douglas Shaper - by TomG - 01-24-2019, 10:02 AM

RE: 10.5" Douglas Shaper - by castellated nut - 01-24-2019, 05:28 PM

Users browsing this thread: 7 Guest(s)