|
Boring a Deep Hole
|
07-19-2013, 12:18 PM
(07-19-2013, 02:45 AM)Hopefuldave Wrote: (cos the bar always flexes the same throughout the bore, same load at same point).Dave, could you elucidate as to why a "one end supported" boring bar, as in a boring head, would flex more (or less) at entry of the bore than at the end/exit? 
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
|
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
Boring a Deep Hole - by EdK - 07-16-2013, 06:23 PM
RE: Boring a Deep Hole - by stevec - 07-16-2013, 07:21 PM
RE: Boring a Deep Hole - by f350ca - 07-16-2013, 07:44 PM
RE: Boring a Deep Hole - by wrustle - 07-16-2013, 07:56 PM
RE: Boring a Deep Hole - by TomG - 07-16-2013, 08:18 PM
RE: Boring a Deep Hole - by PixMan - 07-16-2013, 09:16 PM
RE: Boring a Deep Hole - by EdK - 07-17-2013, 06:09 AM
RE: Boring a Deep Hole - by Mayhem - 07-16-2013, 11:51 PM
RE: Boring a Deep Hole - by big job - 07-17-2013, 05:58 AM
RE: Boring a Deep Hole - by EdK - 07-17-2013, 06:01 AM
RE: Boring a Deep Hole - by PixMan - 07-17-2013, 06:23 AM
RE: Boring a Deep Hole - by EdK - 07-17-2013, 06:36 AM
RE: Boring a Deep Hole - by TomG - 07-17-2013, 06:44 AM
RE: Boring a Deep Hole - by EdK - 07-17-2013, 07:16 AM
RE: Boring a Deep Hole - by PixMan - 07-17-2013, 07:00 AM
RE: Boring a Deep Hole - by EdK - 07-17-2013, 07:24 AM
RE: Boring a Deep Hole - by PixMan - 07-17-2013, 07:21 AM
RE: Boring a Deep Hole - by TomG - 07-17-2013, 07:41 AM
RE: Boring a Deep Hole - by doubleboost - 07-17-2013, 02:54 PM
RE: Boring a Deep Hole - by EdK - 07-17-2013, 04:38 PM
RE: Boring a Deep Hole - by doubleboost - 07-17-2013, 05:10 PM
RE: Boring a Deep Hole - by Hopefuldave - 07-19-2013, 02:45 AM
RE: Boring a Deep Hole - by stevec - 07-19-2013, 12:18 PM
RE: Boring a Deep Hole - by EdK - 07-19-2013, 11:05 AM
RE: Boring a Deep Hole - by doubleboost - 07-19-2013, 03:24 PM
RE: Boring a Deep Hole - by EdK - 07-19-2013, 03:42 PM
RE: Boring a Deep Hole - by doubleboost - 07-19-2013, 03:47 PM
RE: Boring a Deep Hole - by EdK - 07-23-2013, 04:23 PM
RE: Boring a Deep Hole - by wrustle - 07-23-2013, 05:30 PM
RE: Boring a Deep Hole - by EdK - 07-23-2013, 06:50 PM
RE: Boring a Deep Hole - by dallen - 07-23-2013, 07:06 PM
RE: Boring a Deep Hole - by f350ca - 07-23-2013, 09:19 PM
|
