MetalworkingFun Forum › Machinery › Lathes › Lathe Tooling v
Selecting A Parting Tool

Thread Modes
Selecting A Parting Tool
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#14
07-12-2013, 06:52 AM
Aluminum may not work the same. It's so soft that it may not break a chip at all.

Just use the 12L14 first.
Reply
Thanks given by: EdK


Messages In This Thread
Selecting A Parting Tool - by EdK - 07-10-2013, 07:35 PM
RE: Selecting A Parting Tool - by EdK - 07-10-2013, 08:22 PM
RE: Selecting A Parting Tool - by PixMan - 07-11-2013, 08:09 AM
RE: Selecting A Parting Tool - by EdK - 07-11-2013, 09:09 AM
RE: Selecting A Parting Tool - by f350ca - 07-11-2013, 12:15 PM
RE: Selecting A Parting Tool - by stevec - 07-11-2013, 01:22 PM
RE: Selecting A Parting Tool - by EdK - 07-11-2013, 04:59 PM
RE: Selecting A Parting Tool - by PixMan - 07-11-2013, 05:46 PM
RE: Selecting A Parting Tool - by EdK - 07-11-2013, 06:13 PM
RE: Selecting A Parting Tool - by PixMan - 07-11-2013, 06:29 PM
RE: Selecting A Parting Tool - by EdK - 07-11-2013, 06:34 PM
RE: Selecting A Parting Tool - by PixMan - 07-11-2013, 09:53 PM
RE: Selecting A Parting Tool - by EdK - 07-12-2013, 05:27 AM
RE: Selecting A Parting Tool - by PixMan - 07-12-2013, 06:52 AM
RE: Selecting A Parting Tool - by EdK - 07-13-2013, 08:15 PM
RE: Selecting A Parting Tool - by Mayhem - 07-13-2013, 11:11 PM
RE: Selecting A Parting Tool - by EdK - 07-13-2013, 11:15 PM
RE: Selecting A Parting Tool - by PixMan - 07-16-2013, 08:39 AM
RE: Selecting A Parting Tool - by EdK - 07-16-2013, 11:51 AM
RE: Selecting A Parting Tool - by TomG - 07-16-2013, 09:05 AM
RE: Selecting A Parting Tool - by EdK - 07-16-2013, 11:52 AM
RE: Selecting A Parting Tool - by PixMan - 07-16-2013, 09:37 AM
RE: Selecting A Parting Tool - by EdK - 07-16-2013, 12:00 PM
RE: Selecting A Parting Tool - by f350ca - 07-16-2013, 01:20 PM
RE: Selecting A Parting Tool - by PixMan - 07-16-2013, 01:57 PM
RE: Selecting A Parting Tool - by EdK - 07-16-2013, 04:43 PM
RE: Selecting A Parting Tool - by stevec - 07-16-2013, 03:31 PM
RE: Selecting A Parting Tool - by PixMan - 07-16-2013, 07:01 PM
RE: Selecting A Parting Tool - by EdK - 07-17-2013, 07:10 AM
RE: Selecting A Parting Tool - by stevec - 07-16-2013, 07:17 PM
RE: Selecting A Parting Tool - by TomG - 07-17-2013, 07:35 AM
RE: Selecting A Parting Tool - by DaveH - 07-17-2013, 12:22 PM
RE: Selecting A Parting Tool - by PixMan - 07-17-2013, 02:26 PM
RE: Selecting A Parting Tool - by EdK - 07-17-2013, 04:40 PM
RE: Selecting A Parting Tool - by EdK - 07-24-2013, 05:11 PM
RE: Selecting A Parting Tool - by Mayhem - 07-25-2013, 05:59 AM
RE: Selecting A Parting Tool - by PixMan - 07-27-2013, 07:51 AM
RE: Selecting A Parting Tool - by EdK - 07-27-2013, 09:02 AM
Good news, bad news, and idea - by PixMan - 07-27-2013, 02:36 PM
RE: Selecting A Parting Tool - by EdK - 07-27-2013, 03:19 PM
RE: Selecting A Parting Tool - by PixMan - 07-27-2013, 03:58 PM



Users browsing this thread: 11 Guest(s)