|
CNCing my mini mill
|
06-08-2013, 12:52 PM
It did Ed, the first one had a couple of pretty good size shrink spots in it, they milled off ok without loosing to much in thickness. The shrinkage on the first casting was caused by me not cutting the gate and runner deep enough for the part to feed as it cooled off.
DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough! 
|
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
CNCing my mini mill - by dallen - 08-03-2012, 08:45 AM
RE: CNCing my mini mill - by dallen - 08-05-2012, 10:16 AM
RE: CNCing my mini mill - by DaveH - 08-05-2012, 12:21 PM
RE: CNCing my mini mill - by dallen - 08-05-2012, 06:09 PM
RE: CNCing my mini mill - by dallen - 08-06-2012, 04:35 PM
RE: CNCing my mini mill - by Mayhem - 08-07-2012, 07:20 AM
RE: CNCing my mini mill - by dallen - 08-09-2012, 10:00 PM
RE: CNCing my mini mill - by dallen - 08-16-2012, 06:13 PM
RE: CNCing my mini mill - by dallen - 08-18-2012, 07:55 PM
RE: CNCing my mini mill - by DaveH - 08-19-2012, 05:06 PM
RE: CNCing my mini mill - by dallen - 08-19-2012, 07:13 PM
RE: CNCing my mini mill - by dallen - 08-26-2012, 08:37 AM
RE: CNCing my mini mill - by pamrick - 08-26-2012, 12:02 PM
RE: CNCing my mini mill - by dallen - 08-27-2012, 07:37 AM
RE: CNCing my mini mill - by DaveH - 08-27-2012, 01:42 PM
RE: CNCing my mini mill - by pamrick - 08-27-2012, 09:10 PM
RE: CNCing my mini mill - by SnailPowered - 08-28-2012, 12:14 AM
RE: CNCing my mini mill - by dallen - 08-28-2012, 08:35 AM
RE: CNCing my mini mill - by dallen - 09-01-2012, 03:53 PM
RE: CNCing my mini mill - by dallen - 09-04-2012, 10:05 PM
RE: CNCing my mini mill - by SnailPowered - 09-04-2012, 10:17 PM
RE: CNCing my mini mill - by dallen - 09-04-2012, 10:42 PM
RE: CNCing my mini mill - by SnailPowered - 09-04-2012, 11:41 PM
RE: CNCing my mini mill - by dallen - 09-07-2012, 07:31 AM
RE: CNCing my mini mill - by dallen - 09-14-2012, 06:39 PM
RE: CNCing my mini mill - by EdK - 09-14-2012, 07:36 PM
RE: CNCing my mini mill - by dallen - 09-14-2012, 08:25 PM
RE: CNCing my mini mill - by EdK - 09-14-2012, 08:32 PM
RE: CNCing my mini mill - by dallen - 09-14-2012, 08:47 PM
RE: CNCing my mini mill - by EdK - 09-14-2012, 08:56 PM
RE: CNCing my mini mill - by dallen - 09-15-2012, 09:24 AM
RE: CNCing my mini mill - by Rickabilly - 09-17-2012, 08:04 AM
RE: CNCing my mini mill - by dallen - 04-16-2013, 12:10 AM
RE: CNCing my mini mill - by dallen - 04-17-2013, 07:38 AM
RE: CNCing my mini mill - by dallen - 06-08-2013, 11:11 AM
RE: CNCing my mini mill - by EdK - 06-08-2013, 12:47 PM
RE: CNCing my mini mill - by dallen - 06-08-2013, 12:52 PM
RE: CNCing my mini mill - by EdK - 06-08-2013, 12:55 PM
RE: CNCing my mini mill - by dallen - 06-08-2013, 06:09 PM
RE: CNCing my mini mill - by DaveH - 06-10-2013, 02:52 PM
RE: CNCing my mini mill - by dallen - 06-16-2013, 02:21 PM
|
