Help - Machining slim rod on the lathe

Hello There, Guest! Register

Thread Modes

Help - Machining slim rod on the lathe

Mayhem Offline

Offline

purveyor of mischief

Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia

#28

04-04-2013, 09:50 AM

I never knew that a spiral tap would unwind. I suggested a spiral tap as opposed to a spiral point tap, as the hole is blind.

Hunting American dentists since 2015.

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Help - Machining slim rod on the lathe - by Wongster - 03-14-2013, 05:58 AM

RE: Help - Machining slim rod on the lathe - by EdK - 03-14-2013, 06:43 AM

RE: Help - Machining slim rod on the lathe - by Wongster - 03-14-2013, 06:49 AM

RE: Help - Machining slim rod on the lathe - by Mayhem - 03-14-2013, 06:57 AM

RE: Help - Machining slim rod on the lathe - by stevec - 03-14-2013, 07:03 AM

RE: Help - Machining slim rod on the lathe - by Mayhem - 03-14-2013, 07:15 AM

RE: Help - Machining slim rod on the lathe - by Wongster - 03-14-2013, 09:08 AM

RE: Help - Machining slim rod on the lathe - by stevec - 03-14-2013, 10:34 AM

RE: Help - Machining slim rod on the lathe - by Wongster - 03-14-2013, 10:57 AM

RE: Help - Machining slim rod on the lathe - by stevec - 03-14-2013, 01:40 PM

RE: Help - Machining slim rod on the lathe - by DaveH - 03-14-2013, 04:28 PM

RE: Help - Machining slim rod on the lathe - by Wongster - 03-14-2013, 06:13 PM

RE: Help - Machining slim rod on the lathe - by Brian - 03-15-2013, 06:26 AM

RE: Help - Machining slim rod on the lathe - by Wongster - 03-15-2013, 06:40 AM

RE: Help - Machining slim rod on the lathe - by Brian - 03-15-2013, 03:14 PM

RE: Help - Machining slim rod on the lathe - by Wongster - 03-15-2013, 07:41 PM

RE: Help - Machining slim rod on the lathe - by Wongster - 04-01-2013, 03:28 AM

RE: Help - Machining slim rod on the lathe - by stevec - 04-01-2013, 07:16 AM

RE: Help - Machining slim rod on the lathe - by Mayhem - 04-01-2013, 03:42 AM

RE: Help - Machining slim rod on the lathe - by TomG - 04-01-2013, 06:48 AM

RE: Help - Machining slim rod on the lathe - by Wongster - 04-01-2013, 10:52 AM

RE: Help - Machining slim rod on the lathe - by EdK - 04-01-2013, 12:08 PM

RE: Help - Machining slim rod on the lathe - by DaveH - 04-01-2013, 01:12 PM

RE: Help - Machining slim rod on the lathe - by Wongster - 04-01-2013, 07:43 PM

RE: Help - Machining slim rod on the lathe - by f350ca - 04-01-2013, 07:56 PM

RE: Help - Machining slim rod on the lathe - by Tony Wells - 04-03-2013, 01:19 AM

RE: Help - Machining slim rod on the lathe - by Wongster - 04-04-2013, 09:33 AM

RE: Help - Machining slim rod on the lathe - by Mayhem - 04-04-2013, 09:50 AM

RE: Help - Machining slim rod on the lathe - by stevec - 04-04-2013, 01:43 PM

RE: Help - Machining slim rod on the lathe - by f350ca - 04-04-2013, 12:36 PM

RE: Help - Machining slim rod on the lathe - by TomG - 04-04-2013, 04:32 PM

RE: Help - Machining slim rod on the lathe - by Tony Wells - 04-04-2013, 07:19 PM

RE: Help - Machining slim rod on the lathe - by Wongster - 04-05-2013, 10:02 AM

Users browsing this thread: 3 Guest(s)