MetalworkingFun Forum › Machining › Projects v
Making New Gear Change Handles

Thread Modes
Making New Gear Change Handles
EdK Offline
Whipping Boy
*******
Posts: 8,863
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#2
03-23-2013, 03:44 PM
I got the blanks marked up and got one chucked up in the 4-jaw chuck. Does this look safe enough? It's a bit unbalanced so I thought I better ask prior to spinning it up. I need to bore a 12mm blind hole for the shaft and then turn some material off of the thickness of the handle with it chucked up as shown.

Thanks,
Ed

   
Reply
Thanks given by:


Messages In This Thread
Making New Gear Change Handles - by EdK - 03-23-2013, 03:40 PM
RE: Making New Gear Change Handles - by EdK - 03-23-2013, 03:44 PM
RE: Making New Gear Change Handles - by Bill Gruby - 03-23-2013, 03:46 PM
RE: Making New Gear Change Handles - by EdK - 03-23-2013, 04:02 PM
RE: Making New Gear Change Handles - by EdK - 03-23-2013, 04:57 PM
RE: Making New Gear Change Handles - by f350ca - 03-23-2013, 06:10 PM
RE: Making New Gear Change Handles - by EdK - 03-23-2013, 07:09 PM
RE: Making New Gear Change Handles - by stevec - 03-23-2013, 06:50 PM
RE: Making New Gear Change Handles - by EdK - 03-23-2013, 07:07 PM
RE: Making New Gear Change Handles - by TomG - 03-24-2013, 09:28 AM
RE: Making New Gear Change Handles - by EdK - 03-24-2013, 09:31 AM
RE: Making New Gear Change Handles - by EdK - 03-30-2013, 05:05 PM
RE: Making New Gear Change Handles - by Bill Gruby - 03-30-2013, 05:59 PM
RE: Making New Gear Change Handles - by TomG - 03-30-2013, 07:02 PM
RE: Making New Gear Change Handles - by EdK - 03-30-2013, 08:29 PM
RE: Making New Gear Change Handles - by Mayhem - 03-30-2013, 08:36 PM
RE: Making New Gear Change Handles - by EdK - 04-07-2013, 01:19 PM
RE: Making New Gear Change Handles - by f350ca - 04-07-2013, 04:35 PM
RE: Making New Gear Change Handles - by Bill Gruby - 04-07-2013, 05:51 PM
RE: Making New Gear Change Handles - by DaveH - 04-08-2013, 08:06 PM
RE: Making New Gear Change Handles - by PixMan - 04-08-2013, 08:38 PM
RE: Making New Gear Change Handles - by EdK - 04-09-2013, 06:38 AM
RE: Making New Gear Change Handles - by sasquatch - 04-09-2013, 07:31 AM
RE: Making New Gear Change Handles - by Mayhem - 04-09-2013, 07:48 AM
RE: Making New Gear Change Handles - by Dave J - 04-09-2013, 08:42 AM
RE: Making New Gear Change Handles - by EdK - 04-09-2013, 10:22 AM
RE: Making New Gear Change Handles - by Mayhem - 04-09-2013, 10:40 AM
RE: Making New Gear Change Handles - by EdK - 04-09-2013, 11:30 AM



Users browsing this thread: 1 Guest(s)